Merge branch 'sensors' into combined-stable

# Conflicts:
#	arch/arm64/boot/dts/qcom/milos-fairphone-fp6.dts

arch/arm64/boot/dts/qcom/milos-fairphone-fp6.dts

@@ -27,6 +27,34 @@
 		serial1 = &uart11;
 	};
 
+	/*
+	 * The sensor I2C bus sits on TLMM eGPIO pads that have no AP QUP
+	 * function; on the stock OS it is driven by an island QUP of the
+	 * Snapdragon Sensor Core (ADSP). From the AP the pads are only
+	 * usable as software GPIOs, so bit-bang the bus.
+	 * Devices on the bus: QMC6308 magnetometer @ 0x2c, SPL07
+	 * barometer @ 0x76, STK3BCx ALS/proximity @ 0x48.
+	 */
+	i2c-sensors {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 153 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 154 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		pinctrl-0 = <&sensor_i2c_default>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@2c {
+			compatible = "qstcorp,qmc6308";
+			reg = <0x2c>;
+			vdd-supply = <&vreg_l10b>;
+			mount-matrix = "0", "-1", "0",
+				       "1", "0", "0",
+				       "0", "0", "1";
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -209,14 +237,34 @@
 	sound {
 		compatible = "qcom,milos-sndcard", "qcom,sm8450-sndcard";
 		model = "Fairphone (Gen. 6)";
-		// audio-routing = ...
+		audio-routing = "AMIC1", "MIC BIAS1",
+				"AMIC2", "MIC BIAS2",
+				"AMIC3", "MIC BIAS3",
+				"TX SWR_INPUT0", "ADC1_OUTPUT",
+				"TX SWR_INPUT1", "ADC2_OUTPUT",
+				"TX SWR_INPUT2", "ADC3_OUTPUT";
 
 		pinctrl-0 = <&lpi_i2s2_active>;
 		pinctrl-1 = <&lpi_i2s2_sleep>;
 		pinctrl-names = "default",
 				"sleep";
 
-		/*
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			codec {
+				sound-dai = <&wcd9378 1>, <&swr2 0>, <&lpass_txmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
 		i2s-dai-link {
 			link-name = "Senary MI2S Playback";
 
@@ -232,7 +280,29 @@
 				sound-dai = <&q6apm>;
 			};
 		};
-		*/
+	};
+
+	wcd9378: audio-codec {
+		compatible = "qcom,wcd9378-codec";
+
+		pinctrl-0 = <&wcd_reset_n_active>;
+		pinctrl-names = "default";
+
+		reset-gpios = <&tlmm 162 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l8b>;
+		vdd-rxtx-supply = <&vreg_l7b>;
+		vdd-io-supply = <&vreg_l7b>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+
+		qcom,rx-device = <&wcd9378_rx>;
+		qcom,tx-device = <&wcd9378_tx>;
+
+		#sound-dai-cells = <1>;
 	};
 
 	thermal-zones {
@@ -700,9 +770,28 @@
 };
 
 &i2c1 {
-	/* Samsung NFC @ 0x27 */
-
 	status = "okay";
+
+	/*
+	 * Samsung S3NRN4V NFC controller. XI is driven by the RF_CLK2 PMIC
+	 * buffer; the chip has no oscillator of its own and gates the clock
+	 * via its CLK_REQ line, so the clock must be voted on in response
+	 * to it.
+	 */
+	nfc@27 {
+		compatible = "samsung,s3nrn4v";
+		reg = <0x27>;
+
+		clk-req-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		clocks = <&rpmhcc RPMH_RF_CLK2>;
+		en-gpios = <&tlmm 56 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <31 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-0 = <&nfc_clk_req_default>, <&nfc_irq_default>,
+			    <&nfc_pd_default>;
+		pinctrl-names = "default";
+		wake-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &i2c3 {
@@ -1086,11 +1175,56 @@
 	};
 };
 
+&swr1 {
+	status = "okay";
+
+	/* WCD9378 RX */
+	wcd9378_rx: codec@0,4 {
+		compatible = "sdw20217011000";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9378 TX */
+	wcd9378_tx: codec@0,3 {
+		compatible = "sdw20217011000";
+		reg = <0 3>;
+
+		/*
+		 * WCD9378 TX port 1 (ADC1)          <=> SWR2 port 1 (SWRM_TX1)
+		 * WCD9378 TX port 2 (ADC2)          <=> SWR2 port 1
+		 * WCD9378 TX port 3 (ADC3)          <=> SWR2 port 1
+		 * WCD9378 TX port 4 (DMIC0,1, MBHC) <=> SWR2 port 2
+		 * WCD9378 TX port 5 (DMIC2..5)      <=> SWR2 port 3
+		 */
+		qcom,tx-port-mapping = <1 1 1 2 3>;
+	};
+};
+
 &tlmm {
 	gpio-reserved-ranges = <8 4>, /* Fingerprint SPI */
 			       <13 1>, /* NC */
 			       <63 2>; /* WLAN UART */
 
+	nfc_clk_req_default: nfc-clk-req-default-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sensor_i2c_default: sensor-i2c-default-state {
+		/* SDA, SCL; external pull-ups to vreg_l10b */
+		pins = "gpio153", "gpio154";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	ts_active: ts-irq-active-state {
 		pins = "gpio19";
 		function = "gpio";
@@ -1105,6 +1239,13 @@
 		bias-disable;
 	};
 
+	nfc_irq_default: nfc-irq-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	qup_uart11_sleep_cts: qup-uart11-sleep-cts-state {
 		pins = "gpio48";
 		function = "gpio";
@@ -1172,6 +1313,17 @@
 		bias-pull-down;
 	};
 
+	/*
+	 * Pulled up so the NFC chip stays powered down while the line is
+	 * not driven (it is the chip's active-high power-down input).
+	 */
+	nfc_pd_default: nfc-pd-default-state {
+		pins = "gpio56";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
 	sdc2_card_det_n: sdc2-card-det-state {
 		pins = "gpio65";
 		function = "gpio";
@@ -1213,6 +1365,13 @@
 		drive-strength = <2>;
 		bias-pull-down;
 	};
+
+	wcd_reset_n_active: wcd-reset-n-active-state {
+		pins = "gpio162";
+		function = "gpio";
+		drive-strength = <16>;
+		output-high;
+	};
 };
 
 &uart5 {

drivers/iio/magnetometer/Kconfig

@@ -198,6 +198,17 @@ config INFINEON_TLV493D
 	  To compile this driver as a module, choose M here: the module
 	  will be called tlv493d.
 
+config QMC6308
+	tristate "QST QMC6308 3-Axis Magnetic Sensor"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  Say Y here to add support for the QST QMC6308 3-Axis
+	  Magnetic Sensor.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called qmc6308.
+
 config SENSORS_HMC5843
 	tristate
 	select IIO_BUFFER

drivers/iio/magnetometer/Makefile

@@ -26,6 +26,8 @@ obj-$(CONFIG_IIO_ST_MAGN_SPI_3AXIS) += st_magn_spi.o
 
 obj-$(CONFIG_INFINEON_TLV493D)		+= tlv493d.o
 
+obj-$(CONFIG_QMC6308)			+= qmc6308.o
+
 obj-$(CONFIG_SENSORS_HMC5843)		+= hmc5843_core.o
 obj-$(CONFIG_SENSORS_HMC5843_I2C)	+= hmc5843_i2c.o
 obj-$(CONFIG_SENSORS_HMC5843_SPI)	+= hmc5843_spi.o

drivers/iio/magnetometer/qmc6308.c

@@ -0,0 +1,590 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+/*
+ * Support for QST QMC6308 3-Axis Magnetic Sensor on I2C bus.
+ *
+ * Copyright (C) 2026 Jorijn van der Graaf <jorijnvdgraaf@catcrafts.net>
+ *
+ * Datasheet available at
+ * <https://qstcorp.com/upload/pdf/202202/13-52-15%20QMC6308%20Datasheet%20Rev.%20F(1).pdf>
+ */
+
+#include <linux/array_size.h>
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/cleanup.h>
+#include <linux/delay.h>
+#include <linux/dev_printk.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/time.h>
+#include <linux/types.h>
+
+#include <asm/byteorder.h>
+
+#include <linux/iio/iio.h>
+
+#define QMC6308_REG_ID		0x00
+#define QMC6308_REG_X_LSB	0x01
+#define QMC6308_REG_STATUS	0x09
+#define QMC6308_REG_CTRL1	0x0A
+#define QMC6308_REG_CTRL2	0x0B
+#define QMC6308_REG_CTRL3	0x0D
+#define QMC6308_REG_CTRL4	0x29
+
+#define QMC6308_CHIP_ID		0x80
+
+/* Control register 1 */
+#define QMC6308_MODE_MASK	GENMASK(1, 0)
+#define QMC6308_ODR_MASK	GENMASK(3, 2)
+#define QMC6308_OSR1_MASK	GENMASK(5, 4)
+#define QMC6308_OSR2_MASK	GENMASK(7, 6)
+
+#define QMC6308_MODE_SUSPEND	0x00
+#define QMC6308_MODE_NORMAL	0x01
+
+#define QMC6308_ODR_10HZ	0x00
+#define QMC6308_ODR_50HZ	0x01
+#define QMC6308_ODR_100HZ	0x02
+#define QMC6308_ODR_200HZ	0x03
+
+#define QMC6308_OSR1_8		0x00
+#define QMC6308_OSR1_4		0x01
+#define QMC6308_OSR1_2		0x02
+#define QMC6308_OSR1_1		0x03
+
+/* Control register 2 */
+#define QMC6308_SET_RESET_MASK	GENMASK(1, 0)
+#define QMC6308_RNG_MASK	GENMASK(3, 2)
+#define QMC6308_SELF_TEST	BIT(6)
+#define QMC6308_SOFT_RST	BIT(7)
+
+#define QMC6308_SET_RESET_ON	0x00
+
+#define QMC6308_RNG_30G		0x00
+#define QMC6308_RNG_12G		0x01
+#define QMC6308_RNG_8G		0x02
+#define QMC6308_RNG_2G		0x03
+
+/* Status register */
+#define QMC6308_STATUS_DRDY	BIT(0)
+#define QMC6308_STATUS_OVFL	BIT(1)
+
+/*
+ * Power-on completion time (datasheet Table 7), also used as a
+ * conservative bound after soft reset, for which the datasheet
+ * gives no figure.
+ */
+#define QMC6308_POR_US		250
+
+#define QMC6308_AUTOSUSPEND_DELAY_MS	500
+
+struct qmc6308_data {
+	struct regmap *regmap;
+	/*
+	 * Protect data->range/odr/osr.
+	 * Protect poll and read during measurement (reading the status
+	 * register clears DRDY).
+	 */
+	struct mutex mutex;
+	struct iio_mount_matrix orientation;
+	u8 range;
+	u8 odr;
+	u8 osr;
+};
+
+enum qmc6308_axis {
+	QMC6308_AXIS_X,
+	QMC6308_AXIS_Y,
+	QMC6308_AXIS_Z,
+};
+
+static const int qmc6308_odr_avail[] = {
+	[QMC6308_ODR_10HZ] = 10,
+	[QMC6308_ODR_50HZ] = 50,
+	[QMC6308_ODR_100HZ] = 100,
+	[QMC6308_ODR_200HZ] = 200,
+};
+
+static const int qmc6308_osr1_avail[] = {
+	[QMC6308_OSR1_8] = 8,
+	[QMC6308_OSR1_4] = 4,
+	[QMC6308_OSR1_2] = 2,
+	[QMC6308_OSR1_1] = 1,
+};
+
+/*
+ * Sensitivity is 1000/2500/3750/15000 LSB/Gauss for the
+ * +-30/12/8/2 Gauss ranges respectively.
+ */
+static const int qmc6308_scales[][2] = {
+	[QMC6308_RNG_30G] = { 0, 1000000 },
+	[QMC6308_RNG_12G] = { 0, 400000 },
+	[QMC6308_RNG_8G] = { 0, 266667 },
+	[QMC6308_RNG_2G] = { 0, 66667 },
+};
+
+static int qmc6308_set_mode(struct qmc6308_data *data, unsigned int mode)
+{
+	return regmap_update_bits(data->regmap, QMC6308_REG_CTRL1,
+				  QMC6308_MODE_MASK,
+				  FIELD_PREP(QMC6308_MODE_MASK, mode));
+}
+
+static int qmc6308_take_measurement(struct iio_dev *indio_dev, int index,
+				    int *val)
+{
+	struct qmc6308_data *data = iio_priv(indio_dev);
+	struct regmap *map = data->regmap;
+	struct device *dev = regmap_get_device(map);
+	unsigned int status;
+	__le16 buf[3];
+	int ret;
+
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret) {
+		/* EACCES means a read raced runtime PM disable on suspend */
+		if (ret != -EACCES)
+			dev_err(dev, "Failed to power on (%d)\n", ret);
+		return ret;
+	}
+
+	scoped_guard(mutex, &data->mutex) {
+		/* 50ms headroom over the slowest ODR (10Hz) */
+		ret = regmap_read_poll_timeout(map, QMC6308_REG_STATUS,
+					       status,
+					       (status & QMC6308_STATUS_DRDY),
+					       2 * USEC_PER_MSEC,
+					       150 * USEC_PER_MSEC);
+		if (ret)
+			goto out_rpm_put;
+
+		ret = regmap_bulk_read(map, QMC6308_REG_X_LSB, buf,
+				       sizeof(buf));
+		if (ret)
+			goto out_rpm_put;
+
+		if (status & QMC6308_STATUS_OVFL)
+			ret = -ERANGE;
+	}
+
+out_rpm_put:
+	pm_runtime_put_autosuspend(dev);
+	if (ret)
+		return ret;
+
+	*val = (s16)le16_to_cpu(buf[index]);
+
+	return 0;
+}
+
+static int qmc6308_read_raw(struct iio_dev *indio_dev,
+			    const struct iio_chan_spec *chan,
+			    int *val, int *val2, long mask)
+{
+	struct qmc6308_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = qmc6308_take_measurement(indio_dev, chan->address, val);
+		if (ret)
+			return ret;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE: {
+		guard(mutex)(&data->mutex);
+
+		*val = qmc6308_scales[data->range][0];
+		*val2 = qmc6308_scales[data->range][1];
+
+		return IIO_VAL_INT_PLUS_NANO;
+	}
+	case IIO_CHAN_INFO_SAMP_FREQ: {
+		guard(mutex)(&data->mutex);
+
+		*val = qmc6308_odr_avail[data->odr];
+
+		return IIO_VAL_INT;
+	}
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO: {
+		guard(mutex)(&data->mutex);
+
+		*val = qmc6308_osr1_avail[data->osr];
+
+		return IIO_VAL_INT;
+	}
+	default:
+		return -EINVAL;
+	}
+}
+
+static int qmc6308_write_raw(struct iio_dev *indio_dev,
+			     const struct iio_chan_spec *chan,
+			     int val, int val2, long mask)
+{
+	struct qmc6308_data *data = iio_priv(indio_dev);
+	unsigned int status;
+	unsigned int i;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE: {
+		if (val != 0)
+			return -EINVAL;
+
+		for (i = 0; i < ARRAY_SIZE(qmc6308_scales); i++) {
+			if (val2 == qmc6308_scales[i][1])
+				break;
+		}
+		if (i == ARRAY_SIZE(qmc6308_scales))
+			return -EINVAL;
+
+		guard(mutex)(&data->mutex);
+
+		ret = regmap_update_bits(data->regmap, QMC6308_REG_CTRL2,
+					 QMC6308_RNG_MASK,
+					 FIELD_PREP(QMC6308_RNG_MASK, i));
+		if (ret)
+			return ret;
+
+		data->range = i;
+
+		/*
+		 * The data registers still hold (and DRDY still
+		 * advertises) a sample converted at the previous range;
+		 * discard it so that the next read returns data matching
+		 * the new scale.
+		 */
+		return regmap_read(data->regmap, QMC6308_REG_STATUS,
+				   &status);
+	}
+	case IIO_CHAN_INFO_SAMP_FREQ: {
+		for (i = 0; i < ARRAY_SIZE(qmc6308_odr_avail); i++) {
+			if (val == qmc6308_odr_avail[i])
+				break;
+		}
+		if (i == ARRAY_SIZE(qmc6308_odr_avail))
+			return -EINVAL;
+
+		guard(mutex)(&data->mutex);
+
+		ret = regmap_update_bits(data->regmap, QMC6308_REG_CTRL1,
+					 QMC6308_ODR_MASK,
+					 FIELD_PREP(QMC6308_ODR_MASK, i));
+		if (ret)
+			return ret;
+
+		data->odr = i;
+
+		return 0;
+	}
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO: {
+		for (i = 0; i < ARRAY_SIZE(qmc6308_osr1_avail); i++) {
+			if (val == qmc6308_osr1_avail[i])
+				break;
+		}
+		if (i == ARRAY_SIZE(qmc6308_osr1_avail))
+			return -EINVAL;
+
+		guard(mutex)(&data->mutex);
+
+		ret = regmap_update_bits(data->regmap, QMC6308_REG_CTRL1,
+					 QMC6308_OSR1_MASK,
+					 FIELD_PREP(QMC6308_OSR1_MASK, i));
+		if (ret)
+			return ret;
+
+		data->osr = i;
+
+		return 0;
+	}
+	default:
+		return -EINVAL;
+	}
+}
+
+static int qmc6308_read_avail(struct iio_dev *indio_dev,
+			      struct iio_chan_spec const *chan,
+			      const int **vals, int *type, int *length,
+			      long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		*vals = qmc6308_odr_avail;
+		*type = IIO_VAL_INT;
+		*length = ARRAY_SIZE(qmc6308_odr_avail);
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		*vals = qmc6308_osr1_avail;
+		*type = IIO_VAL_INT;
+		*length = ARRAY_SIZE(qmc6308_osr1_avail);
+		return IIO_AVAIL_LIST;
+	case IIO_CHAN_INFO_SCALE:
+		*vals = (const int *)qmc6308_scales;
+		*type = IIO_VAL_INT_PLUS_NANO;
+		*length = ARRAY_SIZE(qmc6308_scales) * 2;
+		return IIO_AVAIL_LIST;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int qmc6308_write_raw_get_fmt(struct iio_dev *indio_dev,
+				     struct iio_chan_spec const *chan,
+				     long mask)
+{
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		return IIO_VAL_INT_PLUS_NANO;
+	default:
+		return IIO_VAL_INT;
+	}
+}
+
+static const struct iio_mount_matrix *
+qmc6308_get_mount_matrix(const struct iio_dev *indio_dev,
+			 const struct iio_chan_spec *chan)
+{
+	struct qmc6308_data *data = iio_priv(indio_dev);
+
+	return &data->orientation;
+}
+
+static const struct iio_chan_spec_ext_info qmc6308_ext_info[] = {
+	IIO_MOUNT_MATRIX(IIO_SHARED_BY_DIR, qmc6308_get_mount_matrix),
+	{ }
+};
+
+static const struct iio_info qmc6308_info = {
+	.read_raw = qmc6308_read_raw,
+	.write_raw = qmc6308_write_raw,
+	.read_avail = qmc6308_read_avail,
+	.write_raw_get_fmt = qmc6308_write_raw_get_fmt,
+};
+
+static int qmc6308_init(struct qmc6308_data *data)
+{
+	struct regmap *map = data->regmap;
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(map, QMC6308_REG_ID, &reg);
+	if (ret)
+		return ret;
+
+	/* Allow unknown IDs so that fallback compatibles work */
+	if (reg != QMC6308_CHIP_ID)
+		dev_warn(regmap_get_device(map),
+			 "Unknown chip id: 0x%02x, continuing\n", reg);
+
+	/* The SOFT_RST bit is not auto-cleared and must be written back 0 */
+	ret = regmap_write(map, QMC6308_REG_CTRL2, QMC6308_SOFT_RST);
+	if (ret)
+		return ret;
+
+	fsleep(QMC6308_POR_US);
+
+	data->range = QMC6308_RNG_30G;
+
+	ret = regmap_write(map, QMC6308_REG_CTRL2,
+			   FIELD_PREP(QMC6308_SET_RESET_MASK,
+				      QMC6308_SET_RESET_ON) |
+			   FIELD_PREP(QMC6308_RNG_MASK, data->range));
+	if (ret)
+		return ret;
+
+	data->odr = QMC6308_ODR_50HZ;
+	data->osr = QMC6308_OSR1_8;
+
+	return regmap_write(map, QMC6308_REG_CTRL1,
+			    FIELD_PREP(QMC6308_MODE_MASK,
+				       QMC6308_MODE_NORMAL) |
+			    FIELD_PREP(QMC6308_ODR_MASK, data->odr) |
+			    FIELD_PREP(QMC6308_OSR1_MASK, data->osr));
+}
+
+static void qmc6308_power_down_action(void *priv)
+{
+	struct qmc6308_data *data = priv;
+
+	if (!pm_runtime_status_suspended(regmap_get_device(data->regmap)))
+		qmc6308_set_mode(data, QMC6308_MODE_SUSPEND);
+}
+
+static bool qmc6308_volatile_reg(struct device *dev, unsigned int reg)
+{
+	return reg >= QMC6308_REG_X_LSB && reg <= QMC6308_REG_STATUS;
+}
+
+static bool qmc6308_writable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case QMC6308_REG_CTRL1:
+	case QMC6308_REG_CTRL2:
+	case QMC6308_REG_CTRL3:
+	case QMC6308_REG_CTRL4:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static const struct regmap_config qmc6308_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = QMC6308_REG_CTRL4,
+	.cache_type = REGCACHE_MAPLE,
+	.volatile_reg = qmc6308_volatile_reg,
+	.writeable_reg = qmc6308_writable_reg,
+};
+
+#define QMC6308_CHANNEL(_axis)                                 \
+	{                                                      \
+		.type = IIO_MAGN,                              \
+		.modified = 1,                                 \
+		.channel2 = IIO_MOD_##_axis,                   \
+		.address = QMC6308_AXIS_##_axis,               \
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),  \
+		.info_mask_shared_by_type =                    \
+			BIT(IIO_CHAN_INFO_SCALE) |             \
+			BIT(IIO_CHAN_INFO_SAMP_FREQ) |         \
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+		.info_mask_shared_by_type_available =          \
+			BIT(IIO_CHAN_INFO_SCALE) |             \
+			BIT(IIO_CHAN_INFO_SAMP_FREQ) |         \
+			BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
+		.ext_info = qmc6308_ext_info,                  \
+	}
+
+static const struct iio_chan_spec qmc6308_channels[] = {
+	QMC6308_CHANNEL(X),
+	QMC6308_CHANNEL(Y),
+	QMC6308_CHANNEL(Z),
+};
+
+static int qmc6308_probe(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	struct qmc6308_data *data;
+	struct iio_dev *indio_dev;
+	struct regmap *map;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, indio_dev);
+
+	map = devm_regmap_init_i2c(client, &qmc6308_regmap_config);
+	if (IS_ERR(map))
+		return dev_err_probe(dev, PTR_ERR(map),
+				     "regmap initialization failed\n");
+
+	ret = devm_regulator_get_enable(dev, "vdd");
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to enable VDD regulator\n");
+
+	fsleep(QMC6308_POR_US);
+
+	data = iio_priv(indio_dev);
+	data->regmap = map;
+
+	ret = devm_mutex_init(dev, &data->mutex);
+	if (ret)
+		return ret;
+
+	ret = iio_read_mount_matrix(dev, &data->orientation);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to read mount matrix\n");
+
+	indio_dev->name = "qmc6308";
+	indio_dev->info = &qmc6308_info;
+	indio_dev->channels = qmc6308_channels;
+	indio_dev->num_channels = ARRAY_SIZE(qmc6308_channels);
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	ret = qmc6308_init(data);
+	if (ret)
+		return dev_err_probe(dev, ret, "qmc6308 init failed\n");
+
+	pm_runtime_set_active(dev);
+
+	ret = devm_add_action_or_reset(dev, qmc6308_power_down_action, data);
+	if (ret)
+		return ret;
+
+	pm_runtime_get_noresume(dev);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_set_autosuspend_delay(dev, QMC6308_AUTOSUSPEND_DELAY_MS);
+	ret = devm_pm_runtime_enable(dev);
+	if (ret)
+		return ret;
+
+	pm_runtime_put_autosuspend(dev);
+
+	return devm_iio_device_register(dev, indio_dev);
+}
+
+static int qmc6308_runtime_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct qmc6308_data *data = iio_priv(indio_dev);
+
+	return qmc6308_set_mode(data, QMC6308_MODE_SUSPEND);
+}
+
+static int qmc6308_runtime_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct qmc6308_data *data = iio_priv(indio_dev);
+	unsigned int status;
+	int ret;
+
+	ret = qmc6308_set_mode(data, QMC6308_MODE_NORMAL);
+	if (ret)
+		return ret;
+
+	/*
+	 * DRDY may still be set for a sample converted before the last
+	 * suspend; clear it so the next read waits for fresh data.
+	 */
+	return regmap_read(data->regmap, QMC6308_REG_STATUS, &status);
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(qmc6308_pm_ops, qmc6308_runtime_suspend,
+				 qmc6308_runtime_resume, NULL);
+
+static const struct of_device_id qmc6308_match[] = {
+	{ .compatible = "qstcorp,qmc6308" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, qmc6308_match);
+
+static const struct i2c_device_id qmc6308_id[] = {
+	{ .name = "qmc6308" },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, qmc6308_id);
+
+static struct i2c_driver qmc6308_driver = {
+	.driver = {
+		.name = "qmc6308",
+		.of_match_table = qmc6308_match,
+		.pm = pm_ptr(&qmc6308_pm_ops),
+	},
+	.id_table = qmc6308_id,
+	.probe = qmc6308_probe,
+};
+module_i2c_driver(qmc6308_driver);
+
+MODULE_DESCRIPTION("QST QMC6308 3-Axis Magnetic Sensor driver");
+MODULE_AUTHOR("Jorijn van der Graaf <jorijnvdgraaf@catcrafts.net>");
+MODULE_LICENSE("Dual BSD/GPL");

drivers/nfc/s3fwrn5/core.c

@@ -122,11 +122,47 @@ static int s3fwrn5_nci_send(struct nci_dev *ndev, struct sk_buff *skb)
 	return 0;
 }
 
+static int s3fwrn5_nci_setup(struct nci_dev *ndev)
+{
+	struct s3fwrn5_info *info = nci_get_drvdata(ndev);
+
+	/*
+	 * Runs after CORE_RESET, before CORE_INIT. The S3NRN4V needs its
+	 * reference clock configured here (the downstream stack does it in the
+	 * bootloader, before CORE_RESET, but this is the earliest hook the NCI
+	 * core offers and the chip accepts it).
+	 */
+	if (info->variant == S3FWRN5_VARIANT_S3NRN4V)
+		return s3fwrn5_nci_clk_cfg(info);
+
+	return 0;
+}
+
 static int s3fwrn5_nci_post_setup(struct nci_dev *ndev)
 {
 	struct s3fwrn5_info *info = nci_get_drvdata(ndev);
 	int ret;
 
+	if (info->variant == S3FWRN5_VARIANT_S3NRN4V) {
+		/*
+		 * The S3NRN4V ships with working firmware behind a bootloader
+		 * protocol this driver does not implement, so there is no
+		 * download step; the NCI core has already done CORE_RESET +
+		 * CORE_INIT. Just (re)load the RF registers via DUAL_OPTION.
+		 */
+		ret = s3fwrn5_nci_rf_configure_dual(info, "sec_s3nrn4v_hwreg.bin",
+						    "sec_s3nrn4v_swreg.bin");
+		/*
+		 * Keep going even if the blobs could not be loaded: the chip
+		 * still enumerates and falls back to the RF registers programmed
+		 * in its flash, so NFC may work anyway.
+		 */
+		if (ret < 0)
+			dev_warn(&ndev->nfc_dev->dev,
+				 "rfreg configure failed (%d)\n", ret);
+		return 0;
+	}
+
 	if (s3fwrn5_firmware_init(info)) {
 		//skip bootloader mode
 		return 0;
@@ -152,13 +188,14 @@ static const struct nci_ops s3fwrn5_nci_ops = {
 	.open = s3fwrn5_nci_open,
 	.close = s3fwrn5_nci_close,
 	.send = s3fwrn5_nci_send,
+	.setup = s3fwrn5_nci_setup,
 	.post_setup = s3fwrn5_nci_post_setup,
 	.prop_ops = s3fwrn5_nci_prop_ops,
 	.n_prop_ops = ARRAY_SIZE(s3fwrn5_nci_prop_ops),
 };
 
 int s3fwrn5_probe(struct nci_dev **ndev, void *phy_id, struct device *pdev,
-	const struct s3fwrn5_phy_ops *phy_ops)
+	const struct s3fwrn5_phy_ops *phy_ops, enum s3fwrn5_variant variant)
 {
 	struct s3fwrn5_info *info;
 	int ret;
@@ -170,6 +207,7 @@ int s3fwrn5_probe(struct nci_dev **ndev, void *phy_id, struct device *pdev,
 	info->phy_id = phy_id;
 	info->pdev = pdev;
 	info->phy_ops = phy_ops;
+	info->variant = variant;
 	mutex_init(&info->mutex);
 
 	s3fwrn5_set_mode(info, S3FWRN5_MODE_COLD);

drivers/nfc/s3fwrn5/i2c.c

@@ -23,9 +23,76 @@ struct s3fwrn5_i2c_phy {
 	struct i2c_client *i2c_dev;
 	struct clk *clk;
 
+	/*
+	 * Optional hardware clock-request handshake. When a CLK_REQ GPIO is
+	 * wired, the chip drives it high while it needs its XI clock -- notably
+	 * to generate the poll/reader carrier -- and the clock is gated on it
+	 * instead of being left always-on (which never lets the chip's TX PLL
+	 * lock on a fresh clock start, leaving it unable to poll).
+	 */
+	struct gpio_desc *gpio_clk_req;
+	bool clk_on;
+	struct mutex clk_lock;	/* serialises clk_on against the CLK_REQ irq */
+
 	unsigned int irq_skip:1;
 };
 
+static void s3fwrn5_i2c_clk_set_locked(struct s3fwrn5_i2c_phy *phy, bool on)
+{
+	lockdep_assert_held(&phy->clk_lock);
+
+	if (on && !phy->clk_on) {
+		int ret = clk_prepare_enable(phy->clk);
+
+		if (ret == 0)
+			phy->clk_on = true;
+		else
+			dev_warn_once(&phy->i2c_dev->dev,
+				      "failed to enable clock (%d); NFC may not poll\n",
+				      ret);
+	} else if (!on && phy->clk_on) {
+		clk_disable_unprepare(phy->clk);
+		phy->clk_on = false;
+	}
+}
+
+/*
+ * Apply the current CLK_REQ level. Reading the GPIO under clk_lock makes
+ * concurrent callers (the CLK_REQ irq thread and the probe-time seeding)
+ * safe: whoever runs last applies a level read after the earlier update,
+ * never a stale one.
+ */
+static void s3fwrn5_i2c_clk_sync(struct s3fwrn5_i2c_phy *phy)
+{
+	int level;
+
+	mutex_lock(&phy->clk_lock);
+	level = gpiod_get_value_cansleep(phy->gpio_clk_req);
+	if (level >= 0)
+		s3fwrn5_i2c_clk_set_locked(phy, level > 0);
+	else
+		dev_warn_once(&phy->i2c_dev->dev,
+			      "failed to read CLK_REQ (%d); keeping clock state\n",
+			      level);
+	mutex_unlock(&phy->clk_lock);
+}
+
+static void s3fwrn5_i2c_clk_disable_action(void *data)
+{
+	struct s3fwrn5_i2c_phy *phy = data;
+
+	mutex_lock(&phy->clk_lock);
+	s3fwrn5_i2c_clk_set_locked(phy, false);
+	mutex_unlock(&phy->clk_lock);
+}
+
+static irqreturn_t s3fwrn5_i2c_clk_req_thread(int irq, void *phy_id)
+{
+	s3fwrn5_i2c_clk_sync(phy_id);
+
+	return IRQ_HANDLED;
+}
+
 static void s3fwrn5_i2c_set_mode(void *phy_id, enum s3fwrn5_mode mode)
 {
 	struct s3fwrn5_i2c_phy *phy = phy_id;
@@ -146,6 +213,7 @@ out:
 
 static int s3fwrn5_i2c_probe(struct i2c_client *client)
 {
+	enum s3fwrn5_variant variant;
 	struct s3fwrn5_i2c_phy *phy;
 	int ret;
 
@@ -172,15 +240,61 @@ static int s3fwrn5_i2c_probe(struct i2c_client *client)
 	 * S3FWRN5 depends on a clock input ("XI" pin) to function properly.
 	 * Depending on the hardware configuration this could be an always-on
 	 * oscillator or some external clock that must be explicitly enabled.
-	 * Make sure the clock is running before starting S3FWRN5.
+	 *
+	 * If a CLK_REQ GPIO is wired, the chip gates the clock itself (driving
+	 * CLK_REQ high when it needs XI); service that handshake. Otherwise just
+	 * make sure the clock is running before starting S3FWRN5.
 	 */
-	phy->clk = devm_clk_get_optional_enabled(&client->dev, NULL);
-	if (IS_ERR(phy->clk))
-		return dev_err_probe(&client->dev, PTR_ERR(phy->clk),
-				     "failed to get clock\n");
+	mutex_init(&phy->clk_lock);
+	phy->gpio_clk_req = devm_gpiod_get_optional(&client->dev, "clk-req",
+						    GPIOD_IN);
+	if (IS_ERR(phy->gpio_clk_req))
+		return PTR_ERR(phy->gpio_clk_req);
 
+	if (phy->gpio_clk_req) {
+		int clk_req_irq;
+
+		phy->clk = devm_clk_get_optional(&client->dev, NULL);
+		if (IS_ERR(phy->clk))
+			return dev_err_probe(&client->dev, PTR_ERR(phy->clk),
+					     "failed to get clock\n");
+
+		/*
+		 * Unlike the always-on branch below, this clock is enabled by
+		 * hand from the CLK_REQ handler, so devm will not disable it on
+		 * unbind. Gate it off explicitly if it is still on at teardown.
+		 */
+		ret = devm_add_action_or_reset(&client->dev,
+					       s3fwrn5_i2c_clk_disable_action,
+					       phy);
+		if (ret)
+			return ret;
+
+		clk_req_irq = gpiod_to_irq(phy->gpio_clk_req);
+		if (clk_req_irq < 0)
+			return clk_req_irq;
+
+		ret = devm_request_threaded_irq(&client->dev, clk_req_irq, NULL,
+						s3fwrn5_i2c_clk_req_thread,
+						IRQF_TRIGGER_RISING |
+						IRQF_TRIGGER_FALLING |
+						IRQF_ONESHOT,
+						"s3fwrn5_clk_req", phy);
+		if (ret)
+			return ret;
+
+		/* Seed the clock state from the current CLK_REQ level. */
+		s3fwrn5_i2c_clk_sync(phy);
+	} else {
+		phy->clk = devm_clk_get_optional_enabled(&client->dev, NULL);
+		if (IS_ERR(phy->clk))
+			return dev_err_probe(&client->dev, PTR_ERR(phy->clk),
+					     "failed to get clock\n");
+	}
+
+	variant = (uintptr_t)i2c_get_match_data(client);
 	ret = s3fwrn5_probe(&phy->common.ndev, phy, &phy->i2c_dev->dev,
-			    &i2c_phy_ops);
+			    &i2c_phy_ops, variant);
 	if (ret < 0)
 		return ret;
 
@@ -205,13 +319,17 @@ static void s3fwrn5_i2c_remove(struct i2c_client *client)
 }
 
 static const struct i2c_device_id s3fwrn5_i2c_id_table[] = {
-	{ S3FWRN5_I2C_DRIVER_NAME },
-	{}
+	{ .name = S3FWRN5_I2C_DRIVER_NAME, .driver_data = S3FWRN5_VARIANT_FWDL },
+	{ .name = "s3nrn4v", .driver_data = S3FWRN5_VARIANT_S3NRN4V },
+	{ }
 };
 MODULE_DEVICE_TABLE(i2c, s3fwrn5_i2c_id_table);
 
-static const struct of_device_id of_s3fwrn5_i2c_match[] __maybe_unused = {
-	{ .compatible = "samsung,s3fwrn5-i2c", },
+static const struct of_device_id of_s3fwrn5_i2c_match[] = {
+	{ .compatible = "samsung,s3fwrn5-i2c",
+	  .data = (void *)S3FWRN5_VARIANT_FWDL, },
+	{ .compatible = "samsung,s3nrn4v",
+	  .data = (void *)S3FWRN5_VARIANT_S3NRN4V, },
 	{}
 };
 MODULE_DEVICE_TABLE(of, of_s3fwrn5_i2c_match);
@@ -219,7 +337,7 @@ MODULE_DEVICE_TABLE(of, of_s3fwrn5_i2c_match);
 static struct i2c_driver s3fwrn5_i2c_driver = {
 	.driver = {
 		.name = S3FWRN5_I2C_DRIVER_NAME,
-		.of_match_table = of_match_ptr(of_s3fwrn5_i2c_match),
+		.of_match_table = of_s3fwrn5_i2c_match,
 	},
 	.probe = s3fwrn5_i2c_probe,
 	.remove = s3fwrn5_i2c_remove,

drivers/nfc/s3fwrn5/nci.c

@@ -8,6 +8,9 @@
 
 #include <linux/completion.h>
 #include <linux/firmware.h>
+#include <linux/minmax.h>
+#include <linux/slab.h>
+#include <linux/unaligned.h>
 
 #include "s3fwrn5.h"
 #include "nci.h"
@@ -20,7 +23,7 @@ static int s3fwrn5_nci_prop_rsp(struct nci_dev *ndev, struct sk_buff *skb)
 	return 0;
 }
 
-const struct nci_driver_ops s3fwrn5_nci_prop_ops[4] = {
+const struct nci_driver_ops s3fwrn5_nci_prop_ops[5] = {
 	{
 		.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
 				NCI_PROP_SET_RFREG),
@@ -41,6 +44,11 @@ const struct nci_driver_ops s3fwrn5_nci_prop_ops[4] = {
 				NCI_PROP_FW_CFG),
 		.rsp = s3fwrn5_nci_prop_rsp,
 	},
+	{
+		.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
+				NCI_PROP_DUAL_OPTION),
+		.rsp = s3fwrn5_nci_prop_rsp,
+	},
 };
 
 #define S3FWRN5_RFREG_SECTION_SIZE 252
@@ -117,3 +125,112 @@ out:
 	release_firmware(fw);
 	return ret;
 }
+
+/*
+ * Configure the reference clock. The S3NRN4V expects the single-byte FW_CFG
+ * form (just the clock-speed selector). The downstream stack sends this in the
+ * bootloader before CORE_RESET; the earliest the mainline NCI core lets us in
+ * is the ->setup hook (after CORE_RESET, before CORE_INIT), which works.
+ */
+int s3fwrn5_nci_clk_cfg(struct s3fwrn5_info *info)
+{
+	u8 clk_speed = NCI_PROP_FW_CFG_CLK_SPEED;
+
+	return nci_prop_cmd(info->ndev, NCI_PROP_FW_CFG, 1, &clk_speed);
+}
+
+/*
+ * S3NRN4V RF register update. The HW and SW register blobs are merged into a
+ * single stream (HW first) and pushed via the DUAL_OPTION command:
+ * START_UPDATE, one SET_OPTION per 252-byte section, then STOP_UPDATE carrying
+ * a 16-bit checksum (running sum of the merged stream as 32-bit words).
+ */
+int s3fwrn5_nci_rf_configure_dual(struct s3fwrn5_info *info,
+				  const char *hw_name, const char *sw_name)
+{
+	const struct firmware *hw_fw = NULL, *sw_fw = NULL;
+	struct nci_prop_dual_set_option_cmd set_option;
+	struct device *dev = &info->ndev->nfc_dev->dev;
+	size_t merged_size, i, len;
+	u8 *merged = NULL;
+	u8 stop_cmd[3];
+	u32 checksum;
+	u8 sub_oid;
+	int ret;
+
+	ret = request_firmware(&hw_fw, hw_name, dev);
+	if (ret < 0)
+		return ret;
+	ret = request_firmware(&sw_fw, sw_name, dev);
+	if (ret < 0)
+		goto out_hw;
+
+	merged_size = hw_fw->size + sw_fw->size;
+
+	/*
+	 * The stream is checksummed as 32-bit words and pushed in at most 256
+	 * sections (the section index is a single byte); reject blobs that
+	 * would silently break either.
+	 */
+	if (merged_size % 4 ||
+	    merged_size > 256 * NCI_PROP_DUAL_SECTION_SIZE) {
+		dev_err(dev, "invalid rfreg blob size (%zu)\n", merged_size);
+		ret = -EINVAL;
+		goto out;
+	}
+
+	merged = kmalloc(merged_size, GFP_KERNEL);
+	if (!merged) {
+		ret = -ENOMEM;
+		goto out;
+	}
+	memcpy(merged, hw_fw->data, hw_fw->size);
+	memcpy(merged + hw_fw->size, sw_fw->data, sw_fw->size);
+
+	/* Running sum of the merged stream as little-endian 32-bit words. */
+	checksum = 0;
+	for (i = 0; i + 4 <= merged_size; i += 4)
+		checksum += get_unaligned_le32(merged + i);
+
+	dev_dbg(dev, "rfreg dual-option update: %s + %s\n", hw_name, sw_name);
+
+	/* START_UPDATE */
+	sub_oid = NCI_PROP_DUAL_SUB_START_UPDATE;
+	ret = nci_prop_cmd(info->ndev, NCI_PROP_DUAL_OPTION, 1, &sub_oid);
+	if (ret < 0) {
+		dev_err(dev, "Unable to start rfreg update\n");
+		goto out;
+	}
+
+	/* SET_OPTION per section */
+	set_option.sub_oid = NCI_PROP_DUAL_SUB_SET_OPTION;
+	set_option.index = 0;
+	for (i = 0; i < merged_size; i += NCI_PROP_DUAL_SECTION_SIZE) {
+		len = min_t(size_t, merged_size - i, NCI_PROP_DUAL_SECTION_SIZE);
+		memcpy(set_option.data, merged + i, len);
+		ret = nci_prop_cmd(info->ndev, NCI_PROP_DUAL_OPTION,
+				   len + 2, (__u8 *)&set_option);
+		if (ret < 0) {
+			dev_err(dev, "rfreg update error (code=%d)\n", ret);
+			goto out;
+		}
+		set_option.index++;
+	}
+
+	/* STOP_UPDATE with checksum */
+	stop_cmd[0] = NCI_PROP_DUAL_SUB_STOP_UPDATE;
+	put_unaligned_le16(checksum, &stop_cmd[1]);
+	ret = nci_prop_cmd(info->ndev, NCI_PROP_DUAL_OPTION, 3, stop_cmd);
+	if (ret < 0) {
+		dev_err(dev, "Unable to stop rfreg update\n");
+		goto out;
+	}
+
+	dev_dbg(dev, "rfreg dual-option update: success\n");
+out:
+	kfree(merged);
+	release_firmware(sw_fw);
+out_hw:
+	release_firmware(hw_fw);
+	return ret;
+}

drivers/nfc/s3fwrn5/nci.h

@@ -40,6 +40,13 @@ struct nci_prop_stop_rfreg_rsp {
 
 #define NCI_PROP_FW_CFG		0x28
 
+/*
+ * Single-byte FW_CFG payload (clock-speed selector) for the S3NRN4V reference
+ * clock. Taken from the vendor configuration for this part (the encoding is
+ * not documented).
+ */
+#define NCI_PROP_FW_CFG_CLK_SPEED	0x11
+
 struct nci_prop_fw_cfg_cmd {
 	__u8 clk_type;
 	__u8 clk_speed;
@@ -50,7 +57,30 @@ struct nci_prop_fw_cfg_rsp {
 	__u8 status;
 };
 
-extern const struct nci_driver_ops s3fwrn5_nci_prop_ops[4];
+/*
+ * The S3NRN4V updates its RF registers through a single "dual option" command
+ * (a sub-OID selects the operation) instead of the START/SET/STOP_RFREG
+ * opcodes above, and expects the HW and SW register blobs merged into one
+ * stream.
+ */
+#define NCI_PROP_DUAL_OPTION		0x2a
+
+#define NCI_PROP_DUAL_SUB_START_UPDATE	0x01
+#define NCI_PROP_DUAL_SUB_SET_OPTION	0x02
+#define NCI_PROP_DUAL_SUB_STOP_UPDATE	0x03
+
+#define NCI_PROP_DUAL_SECTION_SIZE	252
+
+struct nci_prop_dual_set_option_cmd {
+	__u8 sub_oid;	/* NCI_PROP_DUAL_SUB_SET_OPTION */
+	__u8 index;
+	__u8 data[NCI_PROP_DUAL_SECTION_SIZE];
+};
+
+extern const struct nci_driver_ops s3fwrn5_nci_prop_ops[5];
 int s3fwrn5_nci_rf_configure(struct s3fwrn5_info *info, const char *fw_name);
+int s3fwrn5_nci_rf_configure_dual(struct s3fwrn5_info *info,
+				  const char *hw_name, const char *sw_name);
+int s3fwrn5_nci_clk_cfg(struct s3fwrn5_info *info);
 
 #endif /* __LOCAL_S3FWRN5_NCI_H_ */

drivers/nfc/s3fwrn5/s3fwrn5.h

@@ -21,6 +21,17 @@ enum s3fwrn5_mode {
 	S3FWRN5_MODE_FW,
 };
 
+enum s3fwrn5_variant {
+	/* S3FWRN5 / S3FWRN82: firmware is downloaded by this driver */
+	S3FWRN5_VARIANT_FWDL,
+	/*
+	 * S3NRN4V: ships with working firmware behind a bootloader protocol
+	 * this driver does not implement; skip the download, configure the
+	 * clock (FW_CFG) and update the RF registers via the DUAL_OPTION cmd.
+	 */
+	S3FWRN5_VARIANT_S3NRN4V,
+};
+
 struct s3fwrn5_phy_ops {
 	void (*set_wake)(void *id, bool sleep);
 	void (*set_mode)(void *id, enum s3fwrn5_mode);
@@ -36,6 +47,7 @@ struct s3fwrn5_info {
 	const struct s3fwrn5_phy_ops *phy_ops;
 
 	struct s3fwrn5_fw_info fw_info;
+	enum s3fwrn5_variant variant;
 
 	struct mutex mutex;
 };
@@ -78,7 +90,7 @@ static inline int s3fwrn5_write(struct s3fwrn5_info *info, struct sk_buff *skb)
 }
 
 int s3fwrn5_probe(struct nci_dev **ndev, void *phy_id, struct device *pdev,
-	const struct s3fwrn5_phy_ops *phy_ops);
+	const struct s3fwrn5_phy_ops *phy_ops, enum s3fwrn5_variant variant);
 void s3fwrn5_remove(struct nci_dev *ndev);
 
 int s3fwrn5_recv_frame(struct nci_dev *ndev, struct sk_buff *skb,

drivers/nfc/s3fwrn5/uart.c

@@ -137,7 +137,7 @@ static int s3fwrn82_uart_probe(struct serdev_device *serdev)
 	}
 
 	ret = s3fwrn5_probe(&phy->common.ndev, phy, &phy->ser_dev->dev,
-			    &uart_phy_ops);
+			    &uart_phy_ops, S3FWRN5_VARIANT_FWDL);
 	if (ret < 0)
 		goto err_serdev;
 

drivers/soundwire/qcom.c

@@ -976,6 +976,20 @@ static enum sdw_command_response qcom_swrm_xfer_msg(struct sdw_bus *bus,
 	struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
 	int ret, i, len;
 
+	if (msg->page) {
+		ret = qcom_swrm_cmd_fifo_wr_cmd(ctrl, msg->addr_page1,
+						msg->dev_num,
+						SDW_SCP_ADDRPAGE1);
+		if (ret)
+			return SDW_CMD_IGNORED;
+
+		ret = qcom_swrm_cmd_fifo_wr_cmd(ctrl, msg->addr_page2,
+						msg->dev_num,
+						SDW_SCP_ADDRPAGE2);
+		if (ret)
+			return SDW_CMD_IGNORED;
+	}
+
 	if (msg->flags == SDW_MSG_FLAG_READ) {
 		for (i = 0; i < msg->len;) {
 			len = min(msg->len - i, QCOM_SWRM_MAX_RD_LEN);

sound/soc/codecs/Kconfig

@@ -301,6 +301,7 @@ config SND_SOC_ALL_CODECS
 	imply SND_SOC_WCD9335
 	imply SND_SOC_WCD934X
 	imply SND_SOC_WCD937X_SDW
+	imply SND_SOC_WCD9378_SDW
 	imply SND_SOC_WCD938X_SDW
 	imply SND_SOC_WCD939X_SDW
 	imply SND_SOC_LPASS_MACRO_COMMON
@@ -2431,6 +2432,24 @@ config SND_SOC_WCD937X_SDW
 	  via soundwire.
 	  To compile this codec driver say Y or m.
 
+config SND_SOC_WCD9378
+	depends on SND_SOC_WCD9378_SDW
+	tristate
+	depends on SOUNDWIRE || !SOUNDWIRE
+	select SND_SOC_WCD_COMMON
+
+config SND_SOC_WCD9378_SDW
+	tristate "WCD9378 Codec - SDW"
+	select SND_SOC_WCD9378
+	depends on SOUNDWIRE
+	select REGMAP_SOUNDWIRE
+	help
+	  The WCD9378 is an audio codec IC connected to the host over
+	  SoundWire, found on Qualcomm SM7635 boards such as the
+	  Fairphone 6. It has three ADCs for analog microphones, mic
+	  bias supplies, headphone/earpiece outputs and MBHC.
+	  To compile this codec driver say Y or m.
+
 config SND_SOC_WCD938X
 	depends on SND_SOC_WCD938X_SDW
 	tristate

sound/soc/codecs/Makefile

@@ -356,6 +356,8 @@ snd-soc-wcd9335-y := wcd9335.o
 snd-soc-wcd934x-y := wcd934x.o
 snd-soc-wcd937x-y := wcd937x.o
 snd-soc-wcd937x-sdw-y := wcd937x-sdw.o
+snd-soc-wcd9378-y := wcd9378.o
+snd-soc-wcd9378-sdw-y := wcd9378-sdw.o
 snd-soc-wcd938x-y := wcd938x.o
 snd-soc-wcd938x-sdw-y := wcd938x-sdw.o
 snd-soc-wcd939x-y := wcd939x.o
@@ -796,6 +798,11 @@ ifdef CONFIG_SND_SOC_WCD937X_SDW
 # avoid link failure by forcing sdw code built-in when needed
 obj-$(CONFIG_SND_SOC_WCD937X) += snd-soc-wcd937x-sdw.o
 endif
+obj-$(CONFIG_SND_SOC_WCD9378)	+= snd-soc-wcd9378.o
+ifdef CONFIG_SND_SOC_WCD9378_SDW
+# avoid link failure by forcing sdw code built-in when needed
+obj-$(CONFIG_SND_SOC_WCD9378) += snd-soc-wcd9378-sdw.o
+endif
 obj-$(CONFIG_SND_SOC_WCD938X)	+= snd-soc-wcd938x.o
 ifdef CONFIG_SND_SOC_WCD938X_SDW
 # avoid link failure by forcing sdw code built-in when needed

sound/soc/codecs/aw88261.c

@@ -10,9 +10,12 @@
 
 #include <linux/i2c.h>
 #include <linux/firmware.h>
+#include <linux/bitops.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <sound/soc.h>
+#include <sound/pcm_params.h>
+#include <sound/tlv.h>
 #include "aw88261.h"
 #include "aw88395/aw88395_data_type.h"
 #include "aw88395/aw88395_device.h"
@@ -27,64 +30,10 @@ static const struct regmap_config aw88261_remap_config = {
 
 static void aw88261_dev_set_volume(struct aw_device *aw_dev, unsigned int value)
 {
-	struct aw_volume_desc *vol_desc = &aw_dev->volume_desc;
-	unsigned int real_value, volume;
-	unsigned int reg_value;
+	unsigned int volume = min(value, (unsigned int)AW88261_MUTE_VOL);
 
-	volume = min((value + vol_desc->init_volume), (unsigned int)AW88261_MUTE_VOL);
-	real_value = DB_TO_REG_VAL(volume);
-
-	regmap_read(aw_dev->regmap, AW88261_SYSCTRL2_REG, &reg_value);
-
-	real_value = (real_value | (reg_value & AW88261_VOL_START_MASK));
-
-	dev_dbg(aw_dev->dev, "value 0x%x , real_value:0x%x", value, real_value);
-
-	regmap_write(aw_dev->regmap, AW88261_SYSCTRL2_REG, real_value);
-}
-
-static void aw88261_dev_fade_in(struct aw_device *aw_dev)
-{
-	struct aw_volume_desc *desc = &aw_dev->volume_desc;
-	int fade_in_vol = desc->ctl_volume;
-	int fade_step = aw_dev->fade_step;
-	int i;
-
-	if (fade_step == 0 || aw_dev->fade_in_time == 0) {
-		aw88261_dev_set_volume(aw_dev, fade_in_vol);
-		return;
-	}
-
-	for (i = AW88261_MUTE_VOL; i >= fade_in_vol; i -= fade_step) {
-		aw88261_dev_set_volume(aw_dev, i);
-		usleep_range(aw_dev->fade_in_time,
-					aw_dev->fade_in_time + 10);
-	}
-
-	if (i != fade_in_vol)
-		aw88261_dev_set_volume(aw_dev, fade_in_vol);
-}
-
-static void aw88261_dev_fade_out(struct aw_device *aw_dev)
-{
-	struct aw_volume_desc *desc = &aw_dev->volume_desc;
-	int fade_step = aw_dev->fade_step;
-	int i;
-
-	if (fade_step == 0 || aw_dev->fade_out_time == 0) {
-		aw88261_dev_set_volume(aw_dev, AW88261_MUTE_VOL);
-		return;
-	}
-
-	for (i = desc->ctl_volume; i <= AW88261_MUTE_VOL; i += fade_step) {
-		aw88261_dev_set_volume(aw_dev, i);
-		usleep_range(aw_dev->fade_out_time, aw_dev->fade_out_time + 10);
-	}
-
-	if (i != AW88261_MUTE_VOL) {
-		aw88261_dev_set_volume(aw_dev, AW88261_MUTE_VOL);
-		usleep_range(aw_dev->fade_out_time, aw_dev->fade_out_time + 10);
-	}
+	regmap_update_bits(aw_dev->regmap, AW88261_SYSCTRL2_REG,
+		~AW88261_VOL_MASK, DB_TO_REG_VAL(volume));
 }
 
 static void aw88261_dev_i2s_tx_enable(struct aw_device *aw_dev, bool flag)
@@ -120,13 +69,13 @@ static void aw88261_dev_amppd(struct aw_device *aw_dev, bool amppd)
 static void aw88261_dev_mute(struct aw_device *aw_dev, bool is_mute)
 {
 	if (is_mute) {
-		aw88261_dev_fade_out(aw_dev);
+		aw88261_dev_set_volume(aw_dev, AW88261_MUTE_VOL);
 		regmap_update_bits(aw_dev->regmap, AW88261_SYSCTRL_REG,
 				~AW88261_HMUTE_MASK, AW88261_HMUTE_ENABLE_VALUE);
 	} else {
 		regmap_update_bits(aw_dev->regmap, AW88261_SYSCTRL_REG,
 				~AW88261_HMUTE_MASK, AW88261_HMUTE_DISABLE_VALUE);
-		aw88261_dev_fade_in(aw_dev);
+		aw88261_dev_set_volume(aw_dev, aw_dev->volume_desc.ctl_volume);
 	}
 }
 
@@ -151,21 +100,21 @@ static int aw88261_dev_get_iis_status(struct aw_device *aw_dev)
 	if (ret)
 		return ret;
 	if ((reg_val & AW88261_BIT_PLL_CHECK) != AW88261_BIT_PLL_CHECK) {
-		dev_err(aw_dev->dev, "check pll lock fail,reg_val:0x%04x", reg_val);
+		dev_dbg(aw_dev->dev, "check pll lock fail,reg_val:0x%04x", reg_val);
 		return -EINVAL;
 	}
 
 	return ret;
 }
 
-static int aw88261_dev_check_mode1_pll(struct aw_device *aw_dev)
+static int aw88261_dev_check_pll(struct aw_device *aw_dev)
 {
 	int ret, i;
 
 	for (i = 0; i < AW88261_DEV_SYSST_CHECK_MAX; i++) {
 		ret = aw88261_dev_get_iis_status(aw_dev);
 		if (ret) {
-			dev_err(aw_dev->dev, "mode1 iis signal check error");
+			dev_dbg(aw_dev->dev, "mode1 iis signal check error");
 			usleep_range(AW88261_2000_US, AW88261_2000_US + 10);
 		} else {
 			return ret;
@@ -175,71 +124,74 @@ static int aw88261_dev_check_mode1_pll(struct aw_device *aw_dev)
 	return -EPERM;
 }
 
-static int aw88261_dev_check_mode2_pll(struct aw_device *aw_dev)
-{
-	unsigned int reg_val;
-	int ret, i;
-
-	ret = regmap_read(aw_dev->regmap, AW88261_PLLCTRL1_REG, &reg_val);
-	if (ret)
-		return ret;
-
-	reg_val &= (~AW88261_CCO_MUX_MASK);
-	if (reg_val == AW88261_CCO_MUX_DIVIDED_VALUE) {
-		dev_dbg(aw_dev->dev, "CCO_MUX is already divider");
-		return -EPERM;
-	}
-
-	/* change mode2 */
-	ret = regmap_update_bits(aw_dev->regmap, AW88261_PLLCTRL1_REG,
-			~AW88261_CCO_MUX_MASK, AW88261_CCO_MUX_DIVIDED_VALUE);
-	if (ret)
-		return ret;
-
-	for (i = 0; i < AW88261_DEV_SYSST_CHECK_MAX; i++) {
-		ret = aw88261_dev_get_iis_status(aw_dev);
-		if (ret) {
-			dev_err(aw_dev->dev, "mode2 iis signal check error");
-			usleep_range(AW88261_2000_US, AW88261_2000_US + 10);
-		} else {
-			break;
-		}
-	}
-
-	/* change mode1 */
-	ret = regmap_update_bits(aw_dev->regmap, AW88261_PLLCTRL1_REG,
-			~AW88261_CCO_MUX_MASK, AW88261_CCO_MUX_BYPASS_VALUE);
-	if (ret == 0) {
-		usleep_range(AW88261_2000_US, AW88261_2000_US + 10);
-		for (i = 0; i < AW88261_DEV_SYSST_CHECK_MAX; i++) {
-			ret = aw88261_dev_check_mode1_pll(aw_dev);
-			if (ret) {
-				dev_err(aw_dev->dev, "mode2 switch to mode1, iis signal check error");
-				usleep_range(AW88261_2000_US, AW88261_2000_US + 10);
-			} else {
-				break;
-			}
-		}
-	}
-
-	return ret;
-}
-
-static int aw88261_dev_check_syspll(struct aw_device *aw_dev)
+static int aw88261_dev_configure_syspll(struct aw88261 *aw88261)
 {
+	struct aw_device *aw_dev = aw88261->aw_pa;
 	int ret;
 
-	ret = aw88261_dev_check_mode1_pll(aw_dev);
-	if (ret) {
-		dev_dbg(aw_dev->dev, "mode1 check iis failed try switch to mode2 check");
-		ret = aw88261_dev_check_mode2_pll(aw_dev);
-		if (ret) {
-			dev_err(aw_dev->dev, "mode2 check iis failed");
-			return ret;
-		}
-	}
+	/* Configure TDM slots (I2S is represented as no slots) */
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL2_REG,
+			~AW88261_SLOT_NUM_MASK, aw88261->slot_num_value);
+	if (ret)
+		return ret;
 
-	return ret;
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL2_REG,
+			~AW88261_I2S_TX_SLOTVLD_MASK,
+			aw88261->tx_slotvld_mask);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL2_REG,
+			~AW88261_I2S_RXL_SLOTVLD_MASK,
+			aw88261->rxl_slotvld_mask);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL2_REG,
+			~AW88261_I2S_RXR_SLOTVLD_MASK,
+			aw88261->rxr_slotvld_mask);
+	if (ret)
+		return ret;
+
+	/* PLL divider must be used for 8/16/32 kHz modes */
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_PLLCTRL1_REG,
+			~AW88261_CCO_MUX_MASK, aw88261->cco_mux_value);
+	if (ret)
+		return ret;
+
+	/* The word clock (WCK) defines the beginning of a frame */
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL1_REG,
+			~AW88261_I2SSR_MASK, aw88261->sr_value);
+	if (ret)
+		return ret;
+
+	/* The bit clock (BCK) defines the length of a frame */
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL1_REG,
+			~AW88261_I2SBCK_MASK,
+			(aw88261->tdm_bck_value != AW88261_TDM_BCK_UNSET)
+			? aw88261->tdm_bck_value : aw88261->bck_value);
+	if (ret)
+		return ret;
+
+	/* The logical frame size is the width of data for 1 slot */
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL1_REG,
+			~AW88261_I2SFS_MASK, aw88261->fs_value);
+	if (ret)
+		return ret;
+
+	/* The I2S interface mode (Philips standard, LSB/MSB justified) */
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_I2SCTRL1_REG,
+			~AW88261_I2SMD_MASK, aw88261->md_value);
+	if (ret)
+		return ret;
+
+	/* The polarity of the bit clock (BCK) */
+	ret = regmap_update_bits(aw_dev->regmap, AW88261_SYSCTRL_REG,
+			~AW88261_BCKINV_MASK, aw88261->bck_inv_value);
+	if (ret)
+		return ret;
+
+	return aw88261_dev_check_pll(aw_dev);
 }
 
 static int aw88261_dev_check_sysst(struct aw_device *aw_dev)
@@ -254,10 +206,10 @@ static int aw88261_dev_check_sysst(struct aw_device *aw_dev)
 			return ret;
 
 		check_val = reg_val & (~AW88261_BIT_SYSST_CHECK_MASK)
-							& AW88261_BIT_SYSST_CHECK;
-		if (check_val != AW88261_BIT_SYSST_CHECK) {
-			dev_err(aw_dev->dev, "check sysst fail, reg_val=0x%04x, check:0x%x",
-				reg_val, AW88261_BIT_SYSST_CHECK);
+							& AW88261_BIT_PLL_CHECK;
+		if (check_val != AW88261_BIT_PLL_CHECK) {
+			dev_dbg(aw_dev->dev, "check sysst fail, reg_val=0x%04x, check:0x%x",
+				reg_val, AW88261_BIT_PLL_CHECK);
 			usleep_range(AW88261_2000_US, AW88261_2000_US + 10);
 		} else {
 			return 0;
@@ -284,22 +236,22 @@ static void aw88261_reg_force_set(struct aw88261 *aw88261)
 	if (aw88261->frcset_en == AW88261_FRCSET_ENABLE) {
 		/* set FORCE_PWM */
 		regmap_update_bits(aw88261->regmap, AW88261_BSTCTRL3_REG,
-				AW88261_FORCE_PWM_MASK, AW88261_FORCE_PWM_FORCEMINUS_PWM_VALUE);
+				~AW88261_FORCE_PWM_MASK, AW88261_FORCE_PWM_FORCEMINUS_PWM_VALUE);
 		/* set BOOST_OS_WIDTH */
 		regmap_update_bits(aw88261->regmap, AW88261_BSTCTRL5_REG,
-				AW88261_BST_OS_WIDTH_MASK, AW88261_BST_OS_WIDTH_50NS_VALUE);
+				~AW88261_BST_OS_WIDTH_MASK, AW88261_BST_OS_WIDTH_50NS_VALUE);
 		/* set BURST_LOOPR */
 		regmap_update_bits(aw88261->regmap, AW88261_BSTCTRL6_REG,
-				AW88261_BST_LOOPR_MASK, AW88261_BST_LOOPR_340K_VALUE);
+				~AW88261_BST_LOOPR_MASK, AW88261_BST_LOOPR_340K_VALUE);
 		/* set RSQN_DLY */
 		regmap_update_bits(aw88261->regmap, AW88261_BSTCTRL7_REG,
-				AW88261_RSQN_DLY_MASK, AW88261_RSQN_DLY_35NS_VALUE);
+				~AW88261_RSQN_DLY_MASK, AW88261_RSQN_DLY_35NS_VALUE);
 		/* set BURST_SSMODE */
 		regmap_update_bits(aw88261->regmap, AW88261_BSTCTRL8_REG,
-				AW88261_BURST_SSMODE_MASK, AW88261_BURST_SSMODE_FAST_VALUE);
+				~AW88261_BURST_SSMODE_MASK, AW88261_BURST_SSMODE_FAST_VALUE);
 		/* set BST_BURST */
 		regmap_update_bits(aw88261->regmap, AW88261_BSTCTRL9_REG,
-				AW88261_BST_BURST_MASK, AW88261_BST_BURST_30MA_VALUE);
+				~AW88261_BST_BURST_MASK, AW88261_BST_BURST_30MA_VALUE);
 	} else {
 		dev_dbg(aw88261->aw_pa->dev, "needn't set reg value");
 	}
@@ -550,7 +502,7 @@ static int aw88261_dev_start(struct aw88261 *aw88261)
 	int ret;
 
 	if (aw_dev->status == AW88261_DEV_PW_ON) {
-		dev_info(aw_dev->dev, "already power on");
+		dev_dbg(aw_dev->dev, "already power on");
 		return 0;
 	}
 
@@ -558,9 +510,9 @@ static int aw88261_dev_start(struct aw88261 *aw88261)
 	aw88261_dev_pwd(aw_dev, false);
 	usleep_range(AW88261_2000_US, AW88261_2000_US + 10);
 
-	ret = aw88261_dev_check_syspll(aw_dev);
+	ret = aw88261_dev_configure_syspll(aw88261);
 	if (ret) {
-		dev_err(aw_dev->dev, "pll check failed cannot start");
+		dev_dbg(aw_dev->dev, "pll check failed");
 		goto pll_check_fail;
 	}
 
@@ -571,7 +523,7 @@ static int aw88261_dev_start(struct aw88261 *aw88261)
 	/* check i2s status */
 	ret = aw88261_dev_check_sysst(aw_dev);
 	if (ret) {
-		dev_err(aw_dev->dev, "sysst check failed");
+		dev_dbg(aw_dev->dev, "sysst check failed");
 		goto sysst_check_fail;
 	}
 
@@ -672,31 +624,25 @@ static void aw88261_start_pa(struct aw88261 *aw88261)
 	for (i = 0; i < AW88261_START_RETRIES; i++) {
 		ret = aw88261_reg_update(aw88261, aw88261->phase_sync);
 		if (ret) {
-			dev_err(aw88261->aw_pa->dev, "fw update failed, cnt:%d\n", i);
+			dev_dbg(aw88261->aw_pa->dev,
+				"aw88261_reg_update failed, cnt:%d, ret:%d\n", i, ret);
 			continue;
 		}
 		ret = aw88261_dev_start(aw88261);
 		if (ret) {
-			dev_err(aw88261->aw_pa->dev, "aw88261 device start failed. retry = %d", i);
+			dev_dbg(aw88261->aw_pa->dev,
+				"aw88261_dev_start failed, cnt:%d, ret:%d\n", i, ret);
 			continue;
 		} else {
-			dev_info(aw88261->aw_pa->dev, "start success\n");
+			dev_dbg(aw88261->aw_pa->dev, "start success\n");
 			break;
 		}
 	}
+	if (ret != 0)
+		dev_err(aw88261->aw_pa->dev, "start failure (%d)\n", ret);
 }
 
-static void aw88261_startup_work(struct work_struct *work)
-{
-	struct aw88261 *aw88261 =
-		container_of(work, struct aw88261, start_work.work);
-
-	mutex_lock(&aw88261->lock);
-	aw88261_start_pa(aw88261);
-	mutex_unlock(&aw88261->lock);
-}
-
-static void aw88261_start(struct aw88261 *aw88261, bool sync_start)
+static void aw88261_start(struct aw88261 *aw88261)
 {
 	if (aw88261->aw_pa->fw_status != AW88261_DEV_FW_OK)
 		return;
@@ -704,14 +650,226 @@ static void aw88261_start(struct aw88261 *aw88261, bool sync_start)
 	if (aw88261->aw_pa->status == AW88261_DEV_PW_ON)
 		return;
 
-	if (sync_start == AW88261_SYNC_START)
-		aw88261_start_pa(aw88261);
-	else
-		queue_delayed_work(system_dfl_wq,
-			&aw88261->start_work,
-			AW88261_START_WORK_DELAY_MS);
+	aw88261_start_pa(aw88261);
 }
 
+static int aw88261_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
+{
+	struct snd_soc_component *component = dai->component;
+	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
+
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_NF:
+		aw88261->bck_inv_value = AW88261_BCKINV_NOT_INVERT_VALUE;
+		break;
+	case SND_SOC_DAIFMT_IB_NF:
+		aw88261->bck_inv_value = AW88261_BCKINV_INVERTED_VALUE;
+		break;
+	default:
+		dev_err(aw88261->aw_pa->dev, "unsupported invert mode 0x%x\n",
+			fmt & SND_SOC_DAIFMT_INV_MASK);
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_I2S:
+	case SND_SOC_DAIFMT_DSP_A:
+		aw88261->md_value = AW88261_I2SMD_PHILIPS_STANDARD_VALUE;
+		break;
+	case SND_SOC_DAIFMT_MSB:
+	case SND_SOC_DAIFMT_DSP_B:
+		aw88261->md_value = AW88261_I2SMD_MSB_JUSTIFIED_VALUE;
+		break;
+	case SND_SOC_DAIFMT_LSB:
+		aw88261->md_value = AW88261_I2SMD_LSB_JUSTIFIED_VALUE;
+		break;
+	default:
+		dev_err(aw88261->aw_pa->dev, "unsupported DAI format 0x%x\n",
+			fmt & SND_SOC_DAIFMT_FORMAT_MASK);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int aw88261_hw_params(struct snd_pcm_substream *substream,
+	struct snd_pcm_hw_params *params,
+	struct snd_soc_dai *dai)
+{
+	struct snd_soc_component *component = dai->component;
+	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
+
+	if (substream->stream == SNDRV_PCM_STREAM_CAPTURE)
+		return 0;
+
+	aw88261->cco_mux_value = AW88261_CCO_MUX_BYPASS_VALUE;
+	switch (params_rate(params)) {
+	case 8000:
+		aw88261->sr_value = AW88261_I2SSR_8KHZ_VALUE;
+		aw88261->cco_mux_value = AW88261_CCO_MUX_DIVIDED_VALUE;
+		break;
+	case 11025:
+		aw88261->sr_value = AW88261_I2SSR_11P025KHZ_VALUE;
+		break;
+	case 12000:
+		aw88261->sr_value = AW88261_I2SSR_12KHZ_VALUE;
+		break;
+	case 16000:
+		aw88261->sr_value = AW88261_I2SSR_16KHZ_VALUE;
+		aw88261->cco_mux_value = AW88261_CCO_MUX_DIVIDED_VALUE;
+		break;
+	case 22050:
+		aw88261->sr_value = AW88261_I2SSR_22P05KHZ_VALUE;
+		break;
+	case 24000:
+		aw88261->sr_value = AW88261_I2SSR_24KHZ_VALUE;
+		break;
+	case 32000:
+		aw88261->sr_value = AW88261_I2SSR_32KHZ_VALUE;
+		aw88261->cco_mux_value = AW88261_CCO_MUX_DIVIDED_VALUE;
+		break;
+	case 44100:
+		aw88261->sr_value = AW88261_I2SSR_44P1KHZ_VALUE;
+		break;
+	case 48000:
+		aw88261->sr_value = AW88261_I2SSR_48KHZ_VALUE;
+		break;
+	case 96000:
+		aw88261->sr_value = AW88261_I2SSR_96KHZ_VALUE;
+		break;
+	case 192000:
+		aw88261->sr_value = AW88261_I2SSR_192KHZ_VALUE;
+		break;
+	default:
+		dev_err(aw88261->aw_pa->dev, "unsupported sample rate %d\n",
+			params_rate(params));
+		return -EINVAL;
+	}
+
+	switch (params_width(params)) {
+	case 16:
+		aw88261->fs_value = AW88261_I2SFS_16_BITS_VALUE;
+		break;
+	case 20:
+		aw88261->fs_value = AW88261_I2SFS_20_BITS_VALUE;
+		break;
+	case 24:
+		aw88261->fs_value = AW88261_I2SFS_24_BITS_VALUE;
+		break;
+	case 32:
+		aw88261->fs_value = AW88261_I2SFS_32_BITS_VALUE;
+		break;
+	default:
+		dev_err(aw88261->aw_pa->dev, "unsupported bit width %d\n",
+			params_width(params));
+		return -EINVAL;
+	}
+
+	switch (params_physical_width(params)) {
+	case 16:
+		aw88261->bck_value = AW88261_I2SBCK_32FS_VALUE;
+		break;
+	case 24:
+		aw88261->bck_value = AW88261_I2SBCK_48FS_VALUE;
+		break;
+	case 32:
+		aw88261->bck_value = AW88261_I2SBCK_64FS_VALUE;
+		break;
+	default:
+		dev_err(aw88261->aw_pa->dev, "unsupported physical bit width %d\n",
+			params_physical_width(params));
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int aw88261_set_tdm_slot(struct snd_soc_dai *dai,
+	unsigned int tx_mask, unsigned int rx_mask, int slots, int slot_width)
+{
+	struct snd_soc_component *component = dai->component;
+	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
+	int chan;
+
+	switch (slots) {
+	case 0:
+		/* Just reset everything TDM related to I2S values */
+		aw88261->slot_num_value = AW88261_SLOT_NUM_I2S_MODE_VALUE;
+		aw88261->tdm_bck_value = AW88261_TDM_BCK_UNSET;
+		aw88261->tx_slotvld_mask = 0 << AW88261_I2S_TX_SLOTVLD_START_BIT;
+		aw88261->rxl_slotvld_mask = 0 << AW88261_I2S_RXL_SLOTVLD_START_BIT;
+		aw88261->rxr_slotvld_mask = 1 << AW88261_I2S_RXR_SLOTVLD_START_BIT;
+		return 0;
+	case 1:
+		aw88261->slot_num_value = AW88261_SLOT_NUM_TDM1S_VALUE;
+		break;
+	case 2:
+		aw88261->slot_num_value = AW88261_SLOT_NUM_TDM2S_VALUE;
+		break;
+	case 4:
+		aw88261->slot_num_value = AW88261_SLOT_NUM_TDM4S_VALUE;
+		break;
+	case 6:
+		aw88261->slot_num_value = AW88261_SLOT_NUM_TDM6S_VALUE;
+		break;
+	case 8:
+		aw88261->slot_num_value = AW88261_SLOT_NUM_TDM8S_VALUE;
+		break;
+	case 16:
+		aw88261->slot_num_value = AW88261_SLOT_NUM_TDM16S_VALUE;
+		break;
+	default:
+		dev_err(aw88261->aw_pa->dev, "unsupported slot count %d\n", slots);
+		return -EINVAL;
+	}
+
+	switch (slot_width) {
+	case 16:
+		aw88261->tdm_bck_value = AW88261_I2SBCK_32FS_VALUE;
+		break;
+	case 20:
+	case 24:
+		aw88261->tdm_bck_value = AW88261_I2SBCK_48FS_VALUE;
+		break;
+	case 32:
+		aw88261->tdm_bck_value = AW88261_I2SBCK_64FS_VALUE;
+		break;
+	default:
+		dev_err(aw88261->aw_pa->dev, "unsupported slot width %d\n",
+			slot_width);
+		return -EINVAL;
+	}
+
+	if (tx_mask != 0) {
+		if ((chan = __ffs(tx_mask)) > 16)
+			return -EINVAL;
+
+		aw88261->tx_slotvld_mask = chan << AW88261_I2S_TX_SLOTVLD_START_BIT;
+	}
+
+	if (rx_mask != 0) {
+		if ((chan = __ffs(rx_mask)) > 16)
+			return -EINVAL;
+
+		aw88261->rxl_slotvld_mask = chan << AW88261_I2S_RXL_SLOTVLD_START_BIT;
+	}
+
+	if ((rx_mask & ~BIT(chan)) != 0) {
+		if ((chan = __ffs(rx_mask & ~BIT(chan))) > 16)
+			return -EINVAL;
+
+		aw88261->rxr_slotvld_mask = chan << AW88261_I2S_RXR_SLOTVLD_START_BIT;
+	}
+
+	return 0;
+}
+
+static const struct snd_soc_dai_ops aw88261_dai_ops = {
+	.set_fmt = aw88261_set_fmt,
+	.hw_params = aw88261_hw_params,
+	.set_tdm_slot = aw88261_set_tdm_slot,
+};
+
 static struct snd_soc_dai_driver aw88261_dai[] = {
 	{
 		.name = "aw88261-aif",
@@ -730,78 +888,10 @@ static struct snd_soc_dai_driver aw88261_dai[] = {
 			.rates = AW88261_RATES,
 			.formats = AW88261_FORMATS,
 		},
+		.ops = &aw88261_dai_ops,
 	},
 };
 
-static int aw88261_get_fade_in_time(struct snd_kcontrol *kcontrol,
-	struct snd_ctl_elem_value *ucontrol)
-{
-	struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
-	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
-	struct aw_device *aw_dev = aw88261->aw_pa;
-
-	ucontrol->value.integer.value[0] = aw_dev->fade_in_time;
-
-	return 0;
-}
-
-static int aw88261_set_fade_in_time(struct snd_kcontrol *kcontrol,
-	struct snd_ctl_elem_value *ucontrol)
-{
-	struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
-	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
-	struct soc_mixer_control *mc =
-		(struct soc_mixer_control *)kcontrol->private_value;
-	struct aw_device *aw_dev = aw88261->aw_pa;
-	int time;
-
-	time = ucontrol->value.integer.value[0];
-
-	if (time < mc->min || time > mc->max)
-		return -EINVAL;
-
-	if (time != aw_dev->fade_in_time) {
-		aw_dev->fade_in_time = time;
-		return 1;
-	}
-
-	return 0;
-}
-
-static int aw88261_get_fade_out_time(struct snd_kcontrol *kcontrol,
-	struct snd_ctl_elem_value *ucontrol)
-{
-	struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
-	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
-	struct aw_device *aw_dev = aw88261->aw_pa;
-
-	ucontrol->value.integer.value[0] = aw_dev->fade_out_time;
-
-	return 0;
-}
-
-static int aw88261_set_fade_out_time(struct snd_kcontrol *kcontrol,
-	struct snd_ctl_elem_value *ucontrol)
-{
-	struct snd_soc_component *component = snd_kcontrol_chip(kcontrol);
-	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
-	struct soc_mixer_control *mc =
-		(struct soc_mixer_control *)kcontrol->private_value;
-	struct aw_device *aw_dev = aw88261->aw_pa;
-	int time;
-
-	time = ucontrol->value.integer.value[0];
-	if (time < mc->min || time > mc->max)
-		return -EINVAL;
-
-	if (time != aw_dev->fade_out_time) {
-		aw_dev->fade_out_time = time;
-		return 1;
-	}
-
-	return 0;
-}
-
 static int aw88261_dev_set_profile_index(struct aw_device *aw_dev, int index)
 {
 	/* check the index whether is valid */
@@ -880,7 +970,7 @@ static int aw88261_profile_set(struct snd_kcontrol *kcontrol,
 
 	if (aw88261->aw_pa->status) {
 		aw88261_dev_stop(aw88261->aw_pa);
-		aw88261_start(aw88261, AW88261_SYNC_START);
+		aw88261_start(aw88261);
 	}
 
 	mutex_unlock(&aw88261->lock);
@@ -895,7 +985,8 @@ static int aw88261_volume_get(struct snd_kcontrol *kcontrol,
 	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(codec);
 	struct aw_volume_desc *vol_desc = &aw88261->aw_pa->volume_desc;
 
-	ucontrol->value.integer.value[0] = vol_desc->ctl_volume;
+	ucontrol->value.integer.value[0] =
+		(AW88261_MUTE_VOL - vol_desc->ctl_volume) / 2;
 
 	return 0;
 }
@@ -908,13 +999,13 @@ static int aw88261_volume_set(struct snd_kcontrol *kcontrol,
 	struct aw_volume_desc *vol_desc = &aw88261->aw_pa->volume_desc;
 	struct soc_mixer_control *mc =
 		(struct soc_mixer_control *)kcontrol->private_value;
-	int value;
-
-	value = ucontrol->value.integer.value[0];
+	int value = ucontrol->value.integer.value[0];
 
 	if (value < mc->min || value > mc->max)
 		return -EINVAL;
 
+	value = AW88261_MUTE_VOL - (value * 2);
+
 	if (vol_desc->ctl_volume != value) {
 		vol_desc->ctl_volume = value;
 		aw88261_dev_set_volume(aw88261->aw_pa, vol_desc->ctl_volume);
@@ -925,48 +1016,18 @@ static int aw88261_volume_set(struct snd_kcontrol *kcontrol,
 	return 0;
 }
 
-static int aw88261_get_fade_step(struct snd_kcontrol *kcontrol,
-				struct snd_ctl_elem_value *ucontrol)
-{
-	struct snd_soc_component *codec = snd_kcontrol_chip(kcontrol);
-	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(codec);
-
-	ucontrol->value.integer.value[0] = aw88261->aw_pa->fade_step;
-
-	return 0;
-}
-
-static int aw88261_set_fade_step(struct snd_kcontrol *kcontrol,
-				struct snd_ctl_elem_value *ucontrol)
-{
-	struct snd_soc_component *codec = snd_kcontrol_chip(kcontrol);
-	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(codec);
-	struct soc_mixer_control *mc =
-		(struct soc_mixer_control *)kcontrol->private_value;
-	int value;
-
-	value = ucontrol->value.integer.value[0];
-	if (value < mc->min || value > mc->max)
-		return -EINVAL;
-
-	if (aw88261->aw_pa->fade_step != value) {
-		aw88261->aw_pa->fade_step = value;
-		return 1;
-	}
-
-	return 0;
-}
+/*
+ * The field contains 4 bits in units of 6dB + 6 bits in units of 0.125dB
+ * which is too precise for TLV (!) so we have to multiply the scale by 2.
+ *
+ * The range is clamped at -90dB to prevent overflowing the 4-bit part.
+ */
+static const DECLARE_TLV_DB_SCALE(volume_tlv, -9000, 25, 0);
 
 static const struct snd_kcontrol_new aw88261_controls[] = {
-	SOC_SINGLE_EXT("PCM Playback Volume", AW88261_SYSCTRL2_REG,
-		6, AW88261_MUTE_VOL, 0, aw88261_volume_get,
-		aw88261_volume_set),
-	SOC_SINGLE_EXT("Fade Step", 0, 0, AW88261_MUTE_VOL, 0,
-		aw88261_get_fade_step, aw88261_set_fade_step),
-	SOC_SINGLE_EXT("Volume Ramp Up Step", 0, 0, FADE_TIME_MAX, FADE_TIME_MIN,
-		aw88261_get_fade_in_time, aw88261_set_fade_in_time),
-	SOC_SINGLE_EXT("Volume Ramp Down Step", 0, 0, FADE_TIME_MAX, FADE_TIME_MIN,
-		aw88261_get_fade_out_time, aw88261_set_fade_out_time),
+	SOC_SINGLE_EXT_TLV("PCM Playback Volume", AW88261_SYSCTRL2_REG,
+		6, AW88261_CTL_MAX_VOL, 1,
+		aw88261_volume_get, aw88261_volume_set, volume_tlv),
 	AW88261_PROFILE_EXT("Profile Set", aw88261_profile_info,
 		aw88261_profile_get, aw88261_profile_set),
 };
@@ -980,7 +1041,7 @@ static int aw88261_playback_event(struct snd_soc_dapm_widget *w,
 	mutex_lock(&aw88261->lock);
 	switch (event) {
 	case SND_SOC_DAPM_PRE_PMU:
-		aw88261_start(aw88261, AW88261_ASYNC_START);
+		aw88261_start(aw88261);
 		break;
 	case SND_SOC_DAPM_POST_PMD:
 		aw88261_dev_stop(aw88261->aw_pa);
@@ -1057,8 +1118,6 @@ static int aw88261_dev_init(struct aw88261 *aw88261, struct aw_container *aw_cfg
 	if (ret)
 		return ret;
 
-	aw_dev->fade_in_time = AW88261_500_US;
-	aw_dev->fade_out_time = AW88261_500_US;
 	aw_dev->prof_cur = AW88261_INIT_PROFILE;
 	aw_dev->prof_index = AW88261_INIT_PROFILE;
 
@@ -1094,6 +1153,7 @@ static int aw88261_dev_init(struct aw88261 *aw88261, struct aw_container *aw_cfg
 static int aw88261_request_firmware_file(struct aw88261 *aw88261)
 {
 	const struct firmware *cont = NULL;
+	struct aw_container *aw_cfg;
 	const char *fw_name;
 	int ret;
 
@@ -1111,15 +1171,17 @@ static int aw88261_request_firmware_file(struct aw88261 *aw88261)
 	dev_info(aw88261->aw_pa->dev, "loaded %s - size: %zu\n",
 			fw_name, cont ? cont->size : 0);
 
-	aw88261->aw_cfg = devm_kzalloc(aw88261->aw_pa->dev, cont->size + sizeof(int), GFP_KERNEL);
-	if (!aw88261->aw_cfg) {
+	aw_cfg = devm_kzalloc(aw88261->aw_pa->dev, struct_size(aw_cfg, data, cont->size), GFP_KERNEL);
+	if (!aw_cfg) {
 		release_firmware(cont);
 		return -ENOMEM;
 	}
-	aw88261->aw_cfg->len = (int)cont->size;
-	memcpy(aw88261->aw_cfg->data, cont->data, cont->size);
+	aw_cfg->len = (int)cont->size;
+	memcpy(aw_cfg->data, cont->data, cont->size);
 	release_firmware(cont);
 
+	aw88261->aw_cfg = aw_cfg;
+
 	ret = aw88395_dev_load_acf_check(aw88261->aw_pa, aw88261->aw_cfg);
 	if (ret) {
 		dev_err(aw88261->aw_pa->dev, "load [%s] failed !", fw_name);
@@ -1142,8 +1204,6 @@ static int aw88261_codec_probe(struct snd_soc_component *component)
 	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(component);
 	int ret;
 
-	INIT_DELAYED_WORK(&aw88261->start_work, aw88261_startup_work);
-
 	ret = aw88261_request_firmware_file(aw88261);
 	if (ret)
 		return dev_err_probe(aw88261->aw_pa->dev, ret,
@@ -1167,16 +1227,8 @@ static int aw88261_codec_probe(struct snd_soc_component *component)
 	return ret;
 }
 
-static void aw88261_codec_remove(struct snd_soc_component *aw_codec)
-{
-	struct aw88261 *aw88261 = snd_soc_component_get_drvdata(aw_codec);
-
-	cancel_delayed_work_sync(&aw88261->start_work);
-}
-
 static const struct snd_soc_component_driver soc_codec_dev_aw88261 = {
 	.probe = aw88261_codec_probe,
-	.remove = aw88261_codec_remove,
 };
 
 static void aw88261_parse_channel_dt(struct aw88261 *aw88261)
@@ -1208,7 +1260,7 @@ static int aw88261_init(struct aw88261 *aw88261, struct i2c_client *i2c, struct
 		return ret;
 	}
 	if (chip_id != AW88261_CHIP_ID) {
-		dev_err(&i2c->dev, "unsupported device");
+		dev_err(&i2c->dev, "unsupported device id = %x", chip_id);
 		return -ENXIO;
 	}
 
@@ -1229,8 +1281,7 @@ static int aw88261_init(struct aw88261 *aw88261, struct i2c_client *i2c, struct
 	aw_dev->prof_info.prof_type = AW88395_DEV_NONE_TYPE_ID;
 	aw_dev->channel = 0;
 	aw_dev->fw_status = AW88261_DEV_FW_FAILED;
-	aw_dev->fade_step = AW88261_VOLUME_STEP_DB;
-	aw_dev->volume_desc.ctl_volume = AW88261_VOL_DEFAULT_VALUE;
+	aw_dev->volume_desc.ctl_volume = AW88261_CTL_DEFAULT_VOL;
 	aw_dev->volume_desc.mute_volume = AW88261_MUTE_VOL;
 	aw88261_parse_channel_dt(aw88261);
 
@@ -1249,6 +1300,17 @@ static int aw88261_i2c_probe(struct i2c_client *i2c)
 	if (!aw88261)
 		return -ENOMEM;
 
+	/* set defaults */
+	aw88261->slot_num_value = AW88261_SLOT_NUM_I2S_MODE_VALUE;
+	aw88261->sr_value = AW88261_I2SSR_48KHZ_VALUE;
+	aw88261->cco_mux_value = AW88261_CCO_MUX_BYPASS_VALUE;
+	aw88261->fs_value = AW88261_I2SFS_24_BITS_VALUE;
+	aw88261->bck_value = AW88261_I2SBCK_64FS_VALUE;
+	aw88261->bck_inv_value = AW88261_BCKINV_NOT_INVERT_VALUE;
+	aw88261->tdm_bck_value = AW88261_TDM_BCK_UNSET;
+	aw88261->md_value = AW88261_I2SMD_PHILIPS_STANDARD_VALUE;
+	aw88261->rxr_slotvld_mask = 1 << AW88261_I2S_RXR_SLOTVLD_START_BIT;
+
 	mutex_init(&aw88261->lock);
 
 	i2c_set_clientdata(i2c, aw88261);
@@ -1274,7 +1336,7 @@ static int aw88261_i2c_probe(struct i2c_client *i2c)
 }
 
 static const struct i2c_device_id aw88261_i2c_id[] = {
-	{ "aw88261" },
+	{ .name = "aw88261" },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, aw88261_i2c_id);

sound/soc/codecs/aw88261.h

@@ -116,6 +116,19 @@
 #define AW88261_VCALK_SHIFT		(0)
 #define AW88261_VCALKL_SHIFT		(0)
 
+#define AW88261_BCKINV_START_BIT	(4)
+#define AW88261_BCKINV_BITS_LEN	(1)
+#define AW88261_BCKINV_MASK	\
+	(~(((1<<AW88261_BCKINV_BITS_LEN)-1) << AW88261_BCKINV_START_BIT))
+
+#define AW88261_BCKINV_NOT_INVERT	(0)
+#define AW88261_BCKINV_NOT_INVERT_VALUE	\
+	(AW88261_BCKINV_NOT_INVERT << AW88261_BCKINV_START_BIT)
+
+#define AW88261_BCKINV_INVERTED	(1)
+#define AW88261_BCKINV_INVERTED_VALUE	\
+	(AW88261_BCKINV_INVERTED << AW88261_BCKINV_START_BIT)
+
 #define AW88261_AMPPD_START_BIT	(1)
 #define AW88261_AMPPD_BITS_LEN		(1)
 #define AW88261_AMPPD_MASK		\
@@ -181,12 +194,6 @@
 		AW88261_OTHS_OT_VALUE | \
 		AW88261_PLLS_LOCKED_VALUE))
 
-#define AW88261_BIT_SYSST_CHECK \
-		(AW88261_BSTS_FINISHED_VALUE | \
-		AW88261_SWS_SWITCHING_VALUE | \
-		AW88261_CLKS_STABLE_VALUE | \
-		AW88261_PLLS_LOCKED_VALUE)
-
 #define AW88261_ULS_HMUTE_START_BIT	(14)
 #define AW88261_ULS_HMUTE_BITS_LEN	(1)
 #define AW88261_ULS_HMUTE_MASK		\
@@ -249,7 +256,8 @@
 #define AW88261_VOL_MASK		\
 	(~(((1<<AW88261_VOL_BITS_LEN)-1) << AW88261_VOL_START_BIT))
 
-#define AW88261_VOL_DEFAULT_VALUE	(0)
+#define AW88261_CTL_MAX_VOL		(AW88261_MUTE_VOL / 2)
+#define AW88261_CTL_DEFAULT_VOL		(AW88261_CTL_MAX_VOL / 2)
 
 #define AW88261_I2STXEN_START_BIT	(6)
 #define AW88261_I2STXEN_BITS_LEN	(1)
@@ -264,7 +272,148 @@
 #define AW88261_I2STXEN_ENABLE_VALUE	\
 	(AW88261_I2STXEN_ENABLE << AW88261_I2STXEN_START_BIT)
 
-#define AW88261_CCO_MUX_START_BIT	(14)
+#define AW88261_I2SMD_START_BIT	(8)
+#define AW88261_I2SMD_BITS_LEN	(2)
+#define AW88261_I2SMD_MASK	\
+	(~(((1<<AW88261_I2SMD_BITS_LEN)-1) << AW88261_I2SMD_START_BIT))
+
+#define AW88261_I2SMD_PHILIPS_STANDARD	(0)
+#define AW88261_I2SMD_PHILIPS_STANDARD_VALUE	\
+	(AW88261_I2SMD_PHILIPS_STANDARD << AW88261_I2SMD_START_BIT)
+
+#define AW88261_I2SMD_MSB_JUSTIFIED	(1)
+#define AW88261_I2SMD_MSB_JUSTIFIED_VALUE	\
+	(AW88261_I2SMD_MSB_JUSTIFIED << AW88261_I2SMD_START_BIT)
+
+#define AW88261_I2SMD_LSB_JUSTIFIED	(2)
+#define AW88261_I2SMD_LSB_JUSTIFIED_VALUE	\
+	(AW88261_I2SMD_LSB_JUSTIFIED << AW88261_I2SMD_START_BIT)
+
+#define AW88261_I2SFS_START_BIT			(6)
+#define AW88261_I2SFS_BITS_LEN			(2)
+#define AW88261_I2SFS_MASK				\
+	(~(((1<<AW88261_I2SFS_BITS_LEN)-1)<<AW88261_I2SFS_START_BIT))
+
+#define AW88261_I2SFS_16_BITS			(0)
+#define AW88261_I2SFS_16_BITS_VALUE		\
+	(AW88261_I2SFS_16_BITS << AW88261_I2SFS_START_BIT)
+#define AW88261_I2SFS_20_BITS			(1)
+#define AW88261_I2SFS_20_BITS_VALUE		\
+	(AW88261_I2SFS_20_BITS << AW88261_I2SFS_START_BIT)
+#define AW88261_I2SFS_24_BITS			(2)
+#define AW88261_I2SFS_24_BITS_VALUE		\
+	(AW88261_I2SFS_24_BITS << AW88261_I2SFS_START_BIT)
+#define AW88261_I2SFS_32_BITS			(3)
+#define AW88261_I2SFS_32_BITS_VALUE		\
+	(AW88261_I2SFS_32_BITS << AW88261_I2SFS_START_BIT)
+
+#define AW88261_I2SBCK_START_BIT	(4)
+#define AW88261_I2SBCK_BITS_LEN	(2)
+#define AW88261_I2SBCK_MASK	\
+	(~(((1<<AW88261_I2SBCK_BITS_LEN)-1) << AW88261_I2SBCK_START_BIT))
+
+#define AW88261_I2SBCK_32FS	(0)
+#define AW88261_I2SBCK_32FS_VALUE	\
+	(AW88261_I2SBCK_32FS << AW88261_I2SBCK_START_BIT)
+
+#define AW88261_I2SBCK_48FS	(1)
+#define AW88261_I2SBCK_48FS_VALUE	\
+	(AW88261_I2SBCK_48FS << AW88261_I2SBCK_START_BIT)
+
+#define AW88261_I2SBCK_64FS	(2)
+#define AW88261_I2SBCK_64FS_VALUE	\
+	(AW88261_I2SBCK_64FS << AW88261_I2SBCK_START_BIT)
+
+#define AW88261_TDM_BCK_UNSET			UINT_MAX
+
+#define AW88261_I2SSR_START_BIT			(0)
+#define AW88261_I2SSR_BITS_LEN			(4)
+#define AW88261_I2SSR_MASK				\
+	(~(((1<<AW88261_I2SSR_BITS_LEN)-1) << AW88261_I2SSR_START_BIT))
+
+#define AW88261_I2SSR_8KHZ				(0)
+#define AW88261_I2SSR_8KHZ_VALUE		\
+	(AW88261_I2SSR_8KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_11P025KHZ			(1)
+#define AW88261_I2SSR_11P025KHZ_VALUE	\
+	(AW88261_I2SSR_11P025KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_12KHZ				(2)
+#define AW88261_I2SSR_12KHZ_VALUE		\
+	(AW88261_I2SSR_12KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_16KHZ				(3)
+#define AW88261_I2SSR_16KHZ_VALUE		\
+	(AW88261_I2SSR_16KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_22P05KHZ			(4)
+#define AW88261_I2SSR_22P05KHZ_VALUE	\
+	(AW88261_I2SSR_22P05KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_24KHZ				(5)
+#define AW88261_I2SSR_24KHZ_VALUE		\
+	(AW88261_I2SSR_24KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_32KHZ				(6)
+#define AW88261_I2SSR_32KHZ_VALUE		\
+	(AW88261_I2SSR_32KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_44P1KHZ			(7)
+#define AW88261_I2SSR_44P1KHZ_VALUE	\
+	(AW88261_I2SSR_44P1KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_48KHZ				(8)
+#define AW88261_I2SSR_48KHZ_VALUE		\
+	(AW88261_I2SSR_48KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_96KHZ				(9)
+#define AW88261_I2SSR_96KHZ_VALUE		\
+	(AW88261_I2SSR_96KHZ << AW88261_I2SSR_START_BIT)
+#define AW88261_I2SSR_192KHZ			(10)
+#define AW88261_I2SSR_192KHZ_VALUE		\
+	(AW88261_I2SSR_192KHZ << AW88261_I2SSR_START_BIT)
+
+#define AW88261_SLOT_NUM_START_BIT	(12)
+#define AW88261_SLOT_NUM_BITS_LEN	(3)
+#define AW88261_SLOT_NUM_MASK	\
+	(~(((1<<AW88261_SLOT_NUM_BITS_LEN)-1) << AW88261_SLOT_NUM_START_BIT))
+
+#define AW88261_SLOT_NUM_I2S_MODE	(0)
+#define AW88261_SLOT_NUM_I2S_MODE_VALUE	\
+	(AW88261_SLOT_NUM_I2S_MODE << AW88261_SLOT_NUM_START_BIT)
+
+#define AW88261_SLOT_NUM_TDM1S	(1)
+#define AW88261_SLOT_NUM_TDM1S_VALUE	\
+	(AW88261_SLOT_NUM_TDM1S << AW88261_SLOT_NUM_START_BIT)
+
+#define AW88261_SLOT_NUM_TDM2S	(2)
+#define AW88261_SLOT_NUM_TDM2S_VALUE	\
+	(AW88261_SLOT_NUM_TDM2S << AW88261_SLOT_NUM_START_BIT)
+
+#define AW88261_SLOT_NUM_TDM4S	(3)
+#define AW88261_SLOT_NUM_TDM4S_VALUE	\
+	(AW88261_SLOT_NUM_TDM4S << AW88261_SLOT_NUM_START_BIT)
+
+#define AW88261_SLOT_NUM_TDM6S	(4)
+#define AW88261_SLOT_NUM_TDM6S_VALUE	\
+	(AW88261_SLOT_NUM_TDM6S << AW88261_SLOT_NUM_START_BIT)
+
+#define AW88261_SLOT_NUM_TDM8S	(5)
+#define AW88261_SLOT_NUM_TDM8S_VALUE	\
+	(AW88261_SLOT_NUM_TDM8S << AW88261_SLOT_NUM_START_BIT)
+
+#define AW88261_SLOT_NUM_TDM16S	(6)
+#define AW88261_SLOT_NUM_TDM16S_VALUE	\
+	(AW88261_SLOT_NUM_TDM16S << AW88261_SLOT_NUM_START_BIT)
+
+#define AW88261_I2S_TX_SLOTVLD_START_BIT	(8)
+#define AW88261_I2S_TX_SLOTVLD_BITS_LEN	(4)
+#define AW88261_I2S_TX_SLOTVLD_MASK	\
+	(~(((1<<AW88261_I2S_TX_SLOTVLD_BITS_LEN)-1) << AW88261_I2S_TX_SLOTVLD_START_BIT))
+
+#define AW88261_I2S_RXR_SLOTVLD_START_BIT	(4)
+#define AW88261_I2S_RXR_SLOTVLD_BITS_LEN	(4)
+#define AW88261_I2S_RXR_SLOTVLD_MASK	\
+	(~(((1<<AW88261_I2S_RXR_SLOTVLD_BITS_LEN)-1) << AW88261_I2S_RXR_SLOTVLD_START_BIT))
+
+#define AW88261_I2S_RXL_SLOTVLD_START_BIT	(0)
+#define AW88261_I2S_RXL_SLOTVLD_BITS_LEN	(4)
+#define AW88261_I2S_RXL_SLOTVLD_MASK	\
+	(~(((1<<AW88261_I2S_RXL_SLOTVLD_BITS_LEN)-1) << AW88261_I2S_RXL_SLOTVLD_START_BIT))
+
+#define AW88261_CCO_MUX_START_BIT	(6)
 #define AW88261_CCO_MUX_BITS_LEN	(1)
 #define AW88261_CCO_MUX_MASK		\
 	(~(((1<<AW88261_CCO_MUX_BITS_LEN)-1) << AW88261_CCO_MUX_START_BIT))
@@ -370,21 +519,20 @@
 #define AW88261_START_RETRIES		(5)
 #define AW88261_START_WORK_DELAY_MS	(0)
 
+/* NOTE: 192000 has a reg value donwstream but not listed in datasheet */
 #define AW88261_RATES (SNDRV_PCM_RATE_8000_48000 | \
+			SNDRV_PCM_RATE_12000 | \
+			SNDRV_PCM_RATE_24000 | \
 			SNDRV_PCM_RATE_96000)
 #define AW88261_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \
 			SNDRV_PCM_FMTBIT_S24_LE | \
 			SNDRV_PCM_FMTBIT_S32_LE)
 
-#define FADE_TIME_MAX			100000
-#define FADE_TIME_MIN			0
-
 #define AW88261_DEV_DEFAULT_CH		(0)
 #define AW88261_ACF_FILE		"aw88261_acf.bin"
 #define AW88261_DEV_SYSST_CHECK_MAX	(10)
 #define AW88261_SOFT_RESET_VALUE	(0x55aa)
 #define AW88261_REG_TO_DB		(0x3f)
-#define AW88261_VOL_START_MASK		(0xfc00)
 #define AW88261_INIT_PROFILE		(0)
 
 #define REG_VAL_TO_DB(value)		((((value) >> AW88261_VOL_6DB_START) * \
@@ -403,11 +551,6 @@
 	.put = profile_set, \
 }
 
-enum {
-	AW88261_SYNC_START = 0,
-	AW88261_ASYNC_START,
-};
-
 enum aw88261_id {
 	AW88261_CHIP_ID = 0x2113,
 };
@@ -442,7 +585,6 @@ struct aw88261 {
 	struct aw_device *aw_pa;
 	struct mutex lock;
 	struct gpio_desc *reset_gpio;
-	struct delayed_work start_work;
 	struct regmap *regmap;
 	struct aw_container *aw_cfg;
 
@@ -451,6 +593,19 @@ struct aw88261 {
 	unsigned int mute_st;
 	unsigned int amppd_st;
 
+	unsigned int sr_value;
+	unsigned int cco_mux_value;
+	unsigned int fs_value;
+	unsigned int bck_value;
+	unsigned int bck_inv_value;
+	unsigned int tdm_bck_value;
+	unsigned int md_value;
+
+	unsigned int slot_num_value;
+	unsigned int tx_slotvld_mask;
+	unsigned int rxl_slotvld_mask;
+	unsigned int rxr_slotvld_mask;
+
 	bool phase_sync;
 };
 

sound/soc/codecs/wcd9378-sdw.c

@@ -0,0 +1,495 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2026, Jorijn van der Graaf
+ *
+ * SoundWire slave driver for the Qualcomm WCD9378 audio codec.
+ *
+ * The codec presents two SoundWire slaves (RX and TX, mfg 0x0217 part
+ * 0x0110); the SDCA control space is a 32-bit paged register map accessed
+ * through the TX slave.
+ */
+
+#include <linux/component.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/soundwire/sdw.h>
+#include <linux/soundwire/sdw_registers.h>
+#include <linux/soundwire/sdw_type.h>
+#include <sound/pcm_params.h>
+
+#include "wcd-common.h"
+#include "wcd9378.h"
+
+#define WCD9378_SDW_CH(id, pn, cmask, mmask)	\
+	[id] = {				\
+		.port_num = pn,			\
+		.ch_mask = cmask,		\
+		.master_ch_mask = mmask,	\
+	}
+
+/*
+ * Each ADC sits alone on its own TX device port (channel 1); by default
+ * they land on channels 1/2/3 of the same master port (SWRM_TX1 on the
+ * FP6). DMIC/MBHC masks per the downstream qcom,tx_swr_ch_map.
+ */
+static struct wcd_sdw_ch_info wcd9378_sdw_tx_ch_info[] = {
+	WCD9378_SDW_CH(WCD9378_ADC1, WCD9378_ADC_1_PORT, BIT(0), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_ADC2, WCD9378_ADC_2_PORT, BIT(0), BIT(1)),
+	WCD9378_SDW_CH(WCD9378_ADC3, WCD9378_ADC_3_PORT, BIT(0), BIT(2)),
+	WCD9378_SDW_CH(WCD9378_DMIC0, WCD9378_DMIC_0_1_MBHC_PORT, BIT(2), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_DMIC1, WCD9378_DMIC_0_1_MBHC_PORT, BIT(3), BIT(1)),
+	WCD9378_SDW_CH(WCD9378_MBHC, WCD9378_DMIC_0_1_MBHC_PORT, BIT(2), BIT(2)),
+	WCD9378_SDW_CH(WCD9378_DMIC2, WCD9378_DMIC_2_5_PORT, BIT(0), BIT(2)),
+	WCD9378_SDW_CH(WCD9378_DMIC3, WCD9378_DMIC_2_5_PORT, BIT(1), BIT(3)),
+	WCD9378_SDW_CH(WCD9378_DMIC4, WCD9378_DMIC_2_5_PORT, BIT(2), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_DMIC5, WCD9378_DMIC_2_5_PORT, BIT(3), BIT(1)),
+};
+
+static struct wcd_sdw_ch_info wcd9378_sdw_rx_ch_info[] = {
+	WCD9378_SDW_CH(WCD9378_HPH_L, WCD9378_HPH_PORT, BIT(0), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_HPH_R, WCD9378_HPH_PORT, BIT(1), BIT(1)),
+	WCD9378_SDW_CH(WCD9378_CLSH, WCD9378_CLSH_PORT, BIT(0), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_COMP_L, WCD9378_COMP_PORT, BIT(0), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_COMP_R, WCD9378_COMP_PORT, BIT(1), BIT(1)),
+	WCD9378_SDW_CH(WCD9378_LO, WCD9378_LO_PORT, BIT(0), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_DSD_L, WCD9378_DSD_PORT, BIT(0), BIT(0)),
+	WCD9378_SDW_CH(WCD9378_DSD_R, WCD9378_DSD_PORT, BIT(1), BIT(1)),
+};
+
+static struct sdw_dpn_prop wcd9378_dpn_prop[WCD9378_MAX_SWR_PORTS] = {
+	{
+		.num = 1,
+		.type = SDW_DPN_SIMPLE,
+		.min_ch = 1,
+		.max_ch = 8,
+		.simple_ch_prep_sm = true,
+	}, {
+		.num = 2,
+		.type = SDW_DPN_SIMPLE,
+		.min_ch = 1,
+		.max_ch = 4,
+		.simple_ch_prep_sm = true,
+	}, {
+		.num = 3,
+		.type = SDW_DPN_SIMPLE,
+		.min_ch = 1,
+		.max_ch = 4,
+		.simple_ch_prep_sm = true,
+	}, {
+		.num = 4,
+		.type = SDW_DPN_SIMPLE,
+		.min_ch = 1,
+		.max_ch = 4,
+		.simple_ch_prep_sm = true,
+	}, {
+		.num = 5,
+		.type = SDW_DPN_SIMPLE,
+		.min_ch = 1,
+		.max_ch = 4,
+		.simple_ch_prep_sm = true,
+	}
+};
+
+int wcd9378_sdw_hw_params(struct wcd9378_sdw_priv *wcd,
+			  struct snd_pcm_substream *substream,
+			  struct snd_pcm_hw_params *params,
+			  struct snd_soc_dai *dai)
+{
+	struct sdw_port_config port_config[WCD9378_MAX_SWR_PORTS];
+	unsigned long ch_mask;
+	int i, j;
+
+	wcd->sconfig.ch_count = 1;
+	wcd->active_ports = 0;
+	for (i = 0; i < WCD9378_MAX_SWR_PORTS; i++) {
+		ch_mask = wcd->port_config[i].ch_mask;
+		if (!ch_mask)
+			continue;
+
+		for_each_set_bit(j, &ch_mask, 4)
+			wcd->sconfig.ch_count++;
+
+		port_config[wcd->active_ports] = wcd->port_config[i];
+		wcd->active_ports++;
+	}
+
+	wcd->sconfig.bps = 1;
+	wcd->sconfig.frame_rate = params_rate(params);
+	wcd->sconfig.direction = wcd->is_tx ? SDW_DATA_DIR_TX : SDW_DATA_DIR_RX;
+	wcd->sconfig.type = SDW_STREAM_PCM;
+
+	return sdw_stream_add_slave(wcd->sdev, &wcd->sconfig,
+				    &port_config[0], wcd->active_ports,
+				    wcd->sruntime);
+}
+EXPORT_SYMBOL_GPL(wcd9378_sdw_hw_params);
+
+/*
+ * Tell the codec the bus clock: base 19.2 MHz plus a scale (div) per bank.
+ * The downstream driver writes these raw SCP registers on every capture
+ * start; here the bus_config callback covers bank switches.
+ */
+static int wcd9378_bus_config(struct sdw_slave *slave,
+			      struct sdw_bus_params *params)
+{
+	u8 scale;
+
+	switch (params->curr_dr_freq) {
+	case 4800000:
+		scale = WCD9378_SWRS_CLK_SCALE_DIV4;
+		break;
+	case 9600000:
+	default:
+		scale = WCD9378_SWRS_CLK_SCALE_DIV2;
+		break;
+	}
+
+	sdw_write(slave, WCD9378_SWRS_SCP_HOST_CLK_DIV2_CTL(params->next_bank),
+		  0x01);
+	sdw_write(slave, WCD9378_SWRS_SCP_BASE_CLK,
+		  WCD9378_SWRS_BASE_CLK_19P2MHZ);
+	sdw_write(slave, WCD9378_SWRS_SCP_BUSCLK_SCALE_BANK0, scale);
+	sdw_write(slave, WCD9378_SWRS_SCP_BUSCLK_SCALE_BANK1, scale);
+
+	return 0;
+}
+
+static const struct sdw_slave_ops wcd9378_slave_ops = {
+	.update_status = wcd_update_status,
+	.bus_config = wcd9378_bus_config,
+};
+
+static const struct reg_default wcd9378_defaults[] = {
+	{ WCD9378_ANA_BIAS,			0x00 },
+	{ WCD9378_ANA_TX_CH1,			0x20 },
+	{ WCD9378_ANA_TX_CH2,			0x00 },
+	{ WCD9378_ANA_TX_CH3,			0x20 },
+	{ WCD9378_ANA_TX_CH3_HPF,		0x00 },
+	{ WCD9378_ANA_MICB2_RAMP,		0x00 },
+	{ WCD9378_BIAS_VBG_FINE_ADJ,		0x55 },
+	{ WCD9378_MBHC_CTL_SPARE_1,		0x02 },
+	{ WCD9378_MICB1_TEST_CTL_2,		0x00 },
+	{ WCD9378_MICB2_TEST_CTL_2,		0x00 },
+	{ WCD9378_MICB3_TEST_CTL_2,		0x80 },
+	{ WCD9378_TX_COM_TXFE_DIV_CTL,		0x22 },
+	{ WCD9378_SLEEP_CTL,			0x16 },
+	{ WCD9378_TX_NEW_CH12_MUX,		0x11 },
+	{ WCD9378_TX_NEW_CH34_MUX,		0x23 },
+	{ WCD9378_TOP_CLK_CFG,			0x00 },
+	{ WCD9378_CDC_ANA_TX_CLK_CTL,		0x0e },
+	{ WCD9378_CDC_AMIC_CTL,			0x07 },
+	{ WCD9378_PDM_WD_CTL0,			0x0f },
+	{ WCD9378_PDM_WD_CTL1,			0x0f },
+	{ WCD9378_PLATFORM_CTL,			0x01 },
+	{ WCD9378_SYS_USAGE_CTRL,		0x00 },
+	{ WCD9378_HPH_UP_T0,			0x02 },
+	{ WCD9378_HPH_UP_T9,			0x02 },
+	{ WCD9378_HPH_DN_T0,			0x05 },
+	{ WCD9378_MICB_REMAP_TABLE_VAL_3,	0x00 },
+	{ WCD9378_MICB_REMAP_TABLE_VAL_4,	0x00 },
+	{ WCD9378_MICB_REMAP_TABLE_VAL_5,	0x00 },
+	{ WCD9378_SM0_MB_SEL,			0x00 },
+	{ WCD9378_SM1_MB_SEL,			0x00 },
+	{ WCD9378_SM2_MB_SEL,			0x00 },
+	{ WCD9378_MB_PULLUP_EN,			0x00 },
+	{ WCD9378_SMP_AMP_FUNC_ACT,		0x00 },
+	{ WCD9378_CMT_GRP_MASK,			0x00 },
+	{ WCD9378_SMP_JACK_IT31_MICB,		0x00 },
+	{ WCD9378_SMP_JACK_IT31_USAGE,		0x03 },
+	{ WCD9378_SMP_JACK_PDE34_REQ_PS,	0x03 },
+	{ WCD9378_SMP_JACK_FUNC_ACT,		0x00 },
+	{ WCD9378_SMP_MIC_IT11_MICB(0),		0x00 },
+	{ WCD9378_SMP_MIC_IT11_USAGE(0),	0x03 },
+	{ WCD9378_SMP_MIC_PDE11_REQ_PS(0),	0x03 },
+	{ WCD9378_SMP_MIC_FUNC_ACT(0),		0x00 },
+	{ WCD9378_SMP_MIC_IT11_MICB(1),		0x00 },
+	{ WCD9378_SMP_MIC_IT11_USAGE(1),	0x03 },
+	{ WCD9378_SMP_MIC_PDE11_REQ_PS(1),	0x03 },
+	{ WCD9378_SMP_MIC_FUNC_ACT(1),		0x00 },
+	{ WCD9378_SMP_MIC_IT11_MICB(2),		0x00 },
+	{ WCD9378_SMP_MIC_IT11_USAGE(2),	0x03 },
+	{ WCD9378_SMP_MIC_PDE11_REQ_PS(2),	0x03 },
+	{ WCD9378_SMP_MIC_FUNC_ACT(2),		0x00 },
+};
+
+static bool wcd9378_rdwr_register(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case WCD9378_ANA_BIAS:
+	case WCD9378_ANA_TX_CH1:
+	case WCD9378_ANA_TX_CH2:
+	case WCD9378_ANA_TX_CH3:
+	case WCD9378_ANA_TX_CH3_HPF:
+	case WCD9378_ANA_MICB2_RAMP:
+	case WCD9378_BIAS_VBG_FINE_ADJ:
+	case WCD9378_MBHC_CTL_SPARE_1:
+	case WCD9378_MICB1_TEST_CTL_2:
+	case WCD9378_MICB2_TEST_CTL_2:
+	case WCD9378_MICB3_TEST_CTL_2:
+	case WCD9378_TX_COM_TXFE_DIV_CTL:
+	case WCD9378_SLEEP_CTL:
+	case WCD9378_TX_NEW_CH12_MUX:
+	case WCD9378_TX_NEW_CH34_MUX:
+	case WCD9378_HPH_RDAC_GAIN_CTL:
+	case WCD9378_HPH_RDAC_HD2_CTL_L:
+	case WCD9378_HPH_RDAC_HD2_CTL_R:
+	case WCD9378_TOP_CLK_CFG:
+	case WCD9378_CDC_ANA_TX_CLK_CTL:
+	case WCD9378_CDC_AMIC_CTL:
+	case WCD9378_PDM_WD_CTL0:
+	case WCD9378_PDM_WD_CTL1:
+	case WCD9378_PLATFORM_CTL:
+	case WCD9378_SYS_USAGE_CTRL:
+	case WCD9378_HPH_UP_T0:
+	case WCD9378_HPH_UP_T9:
+	case WCD9378_HPH_DN_T0:
+	case WCD9378_MICB_REMAP_TABLE_VAL_3:
+	case WCD9378_MICB_REMAP_TABLE_VAL_4:
+	case WCD9378_MICB_REMAP_TABLE_VAL_5:
+	case WCD9378_SM0_MB_SEL:
+	case WCD9378_SM1_MB_SEL:
+	case WCD9378_SM2_MB_SEL:
+	case WCD9378_MB_PULLUP_EN:
+	case WCD9378_SMP_AMP_FUNC_STAT:
+	case WCD9378_SMP_AMP_FUNC_ACT:
+	case WCD9378_CMT_GRP_MASK:
+	case WCD9378_SMP_JACK_IT31_MICB:
+	case WCD9378_SMP_JACK_IT31_USAGE:
+	case WCD9378_SMP_JACK_PDE34_REQ_PS:
+	case WCD9378_SMP_JACK_FUNC_STAT:
+	case WCD9378_SMP_JACK_FUNC_ACT:
+	case WCD9378_SMP_MIC_IT11_MICB(0):
+	case WCD9378_SMP_MIC_IT11_USAGE(0):
+	case WCD9378_SMP_MIC_PDE11_REQ_PS(0):
+	case WCD9378_SMP_MIC_FUNC_STAT(0):
+	case WCD9378_SMP_MIC_FUNC_ACT(0):
+	case WCD9378_SMP_MIC_IT11_MICB(1):
+	case WCD9378_SMP_MIC_IT11_USAGE(1):
+	case WCD9378_SMP_MIC_PDE11_REQ_PS(1):
+	case WCD9378_SMP_MIC_FUNC_STAT(1):
+	case WCD9378_SMP_MIC_FUNC_ACT(1):
+	case WCD9378_SMP_MIC_IT11_MICB(2):
+	case WCD9378_SMP_MIC_IT11_USAGE(2):
+	case WCD9378_SMP_MIC_PDE11_REQ_PS(2):
+	case WCD9378_SMP_MIC_FUNC_STAT(2):
+	case WCD9378_SMP_MIC_FUNC_ACT(2):
+		return true;
+	}
+
+	return false;
+}
+
+static bool wcd9378_volatile_register(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case WCD9378_FUNC_EXT_ID_0:
+	case WCD9378_FUNC_EXT_ID_1:
+	case WCD9378_FUNC_EXT_VER:
+	case WCD9378_FUNC_STAT:
+	case WCD9378_DEV_MANU_ID_0:
+	case WCD9378_DEV_MANU_ID_1:
+	case WCD9378_DEV_PART_ID_0:
+	case WCD9378_DEV_PART_ID_1:
+	case WCD9378_DEV_VER:
+	case WCD9378_EFUSE_REG_16:
+	case WCD9378_EFUSE_REG_29:
+	case WCD9378_SEQ_TX0_STAT:
+	case WCD9378_SEQ_TX1_STAT:
+	case WCD9378_SEQ_TX2_STAT:
+	case WCD9378_SMP_AMP_FUNC_STAT:
+	case WCD9378_SMP_JACK_FUNC_STAT:
+	case WCD9378_SMP_JACK_PDE34_ACT_PS:
+	case WCD9378_SMP_MIC_FUNC_STAT(0):
+	case WCD9378_SMP_MIC_FUNC_STAT(1):
+	case WCD9378_SMP_MIC_FUNC_STAT(2):
+	case WCD9378_SMP_MIC_OT10_USAGE(0):
+	case WCD9378_SMP_MIC_PDE11_ACT_PS(0):
+	case WCD9378_SMP_MIC_OT10_USAGE(1):
+	case WCD9378_SMP_MIC_PDE11_ACT_PS(1):
+	case WCD9378_SMP_MIC_OT10_USAGE(2):
+	case WCD9378_SMP_MIC_PDE11_ACT_PS(2):
+		return true;
+	}
+
+	return false;
+}
+
+static bool wcd9378_readable_register(struct device *dev, unsigned int reg)
+{
+	if (wcd9378_volatile_register(dev, reg))
+		return true;
+
+	return wcd9378_rdwr_register(dev, reg);
+}
+
+static const struct regmap_config wcd9378_regmap_config = {
+	.name = "wcd9378_csr",
+	.reg_bits = 32,
+	.val_bits = 8,
+	.cache_type = REGCACHE_MAPLE,
+	.reg_defaults = wcd9378_defaults,
+	.num_reg_defaults = ARRAY_SIZE(wcd9378_defaults),
+	.max_register = WCD9378_MAX_REGISTER,
+	.readable_reg = wcd9378_readable_register,
+	.writeable_reg = wcd9378_rdwr_register,
+	.volatile_reg = wcd9378_volatile_register,
+};
+
+static int wcd9378_sdw_probe(struct sdw_slave *pdev,
+			     const struct sdw_device_id *id)
+{
+	struct device *dev = &pdev->dev;
+	struct wcd9378_sdw_priv *wcd;
+	u8 master_ch_mask[WCD9378_MAX_SWR_CH_IDS];
+	int master_ch_mask_size = 0;
+	int ret, i;
+
+	wcd = devm_kzalloc(dev, sizeof(*wcd), GFP_KERNEL);
+	if (!wcd)
+		return -ENOMEM;
+
+	/* Port map index starts at 0, however the data ports start at index 1 */
+	if (of_property_present(dev->of_node, "qcom,tx-port-mapping")) {
+		wcd->is_tx = true;
+		ret = of_property_read_u32_array(dev->of_node, "qcom,tx-port-mapping",
+						 &pdev->m_port_map[1],
+						 WCD9378_MAX_TX_SWR_PORTS);
+	} else {
+		ret = of_property_read_u32_array(dev->of_node, "qcom,rx-port-mapping",
+						 &pdev->m_port_map[1],
+						 WCD9378_MAX_SWR_PORTS);
+	}
+	if (ret < 0)
+		dev_info(dev, "Error getting static port mapping for %s (%d)\n",
+			 wcd->is_tx ? "TX" : "RX", ret);
+
+	wcd->sdev = pdev;
+	dev_set_drvdata(dev, wcd);
+
+	pdev->prop.scp_int1_mask = SDW_SCP_INT1_BUS_CLASH |
+				   SDW_SCP_INT1_PARITY;
+	pdev->prop.lane_control_support = true;
+	pdev->prop.simple_clk_stop_capable = true;
+	/* The SDCA control space sits above the 16-bit address range */
+	pdev->prop.paging_support = true;
+
+	memset(master_ch_mask, 0, WCD9378_MAX_SWR_CH_IDS);
+
+	if (wcd->is_tx) {
+		master_ch_mask_size = of_property_count_u8_elems(dev->of_node,
+								 "qcom,tx-channel-mapping");
+		master_ch_mask_size = min_t(int, master_ch_mask_size,
+					    ARRAY_SIZE(wcd9378_sdw_tx_ch_info));
+
+		if (master_ch_mask_size > 0)
+			ret = of_property_read_u8_array(dev->of_node,
+							"qcom,tx-channel-mapping",
+							master_ch_mask,
+							master_ch_mask_size);
+	} else {
+		master_ch_mask_size = of_property_count_u8_elems(dev->of_node,
+								 "qcom,rx-channel-mapping");
+		master_ch_mask_size = min_t(int, master_ch_mask_size,
+					    ARRAY_SIZE(wcd9378_sdw_rx_ch_info));
+
+		if (master_ch_mask_size > 0)
+			ret = of_property_read_u8_array(dev->of_node,
+							"qcom,rx-channel-mapping",
+							master_ch_mask,
+							master_ch_mask_size);
+	}
+
+	if (wcd->is_tx) {
+		pdev->prop.source_ports = GENMASK(WCD9378_MAX_TX_SWR_PORTS, 1);
+		pdev->prop.src_dpn_prop = wcd9378_dpn_prop;
+		wcd->ch_info = &wcd9378_sdw_tx_ch_info[0];
+
+		for (i = 0; i < master_ch_mask_size; i++)
+			wcd->ch_info[i].master_ch_mask = WCD9378_SWRM_CH_MASK(master_ch_mask[i]);
+
+		pdev->prop.wake_capable = true;
+
+		wcd->regmap = devm_regmap_init_sdw(pdev, &wcd9378_regmap_config);
+		if (IS_ERR(wcd->regmap))
+			return dev_err_probe(dev, PTR_ERR(wcd->regmap),
+					     "Regmap init failed\n");
+
+		/* Start in cache-only until device is enumerated */
+		regcache_cache_only(wcd->regmap, true);
+	} else {
+		pdev->prop.sink_ports = GENMASK(WCD9378_MAX_SWR_PORTS, 1);
+		pdev->prop.sink_dpn_prop = wcd9378_dpn_prop;
+		wcd->ch_info = &wcd9378_sdw_rx_ch_info[0];
+
+		for (i = 0; i < master_ch_mask_size; i++)
+			wcd->ch_info[i].master_ch_mask = WCD9378_SWRM_CH_MASK(master_ch_mask[i]);
+	}
+
+	ret = component_add(dev, &wcd_sdw_component_ops);
+	if (ret)
+		return ret;
+
+	/* Set suspended until aggregate device is bind */
+	pm_runtime_set_suspended(dev);
+
+	return 0;
+}
+
+static void wcd9378_sdw_remove(struct sdw_slave *pdev)
+{
+	struct device *dev = &pdev->dev;
+
+	component_del(dev, &wcd_sdw_component_ops);
+}
+
+static const struct sdw_device_id wcd9378_sdw_id[] = {
+	SDW_SLAVE_ENTRY(0x0217, 0x0110, 0),
+	{ },
+};
+MODULE_DEVICE_TABLE(sdw, wcd9378_sdw_id);
+
+static int wcd9378_sdw_runtime_suspend(struct device *dev)
+{
+	struct wcd9378_sdw_priv *wcd = dev_get_drvdata(dev);
+
+	if (wcd->regmap) {
+		regcache_cache_only(wcd->regmap, true);
+		regcache_mark_dirty(wcd->regmap);
+	}
+
+	return 0;
+}
+
+static int wcd9378_sdw_runtime_resume(struct device *dev)
+{
+	struct wcd9378_sdw_priv *wcd = dev_get_drvdata(dev);
+
+	if (wcd->regmap) {
+		regcache_cache_only(wcd->regmap, false);
+		regcache_sync(wcd->regmap);
+	}
+
+	return 0;
+}
+
+static const struct dev_pm_ops wcd9378_sdw_pm_ops = {
+	RUNTIME_PM_OPS(wcd9378_sdw_runtime_suspend, wcd9378_sdw_runtime_resume, NULL)
+};
+
+static struct sdw_driver wcd9378_sdw_driver = {
+	.probe = wcd9378_sdw_probe,
+	.remove = wcd9378_sdw_remove,
+	.ops = &wcd9378_slave_ops,
+	.id_table = wcd9378_sdw_id,
+	.driver = {
+		.name = "wcd9378-sdw",
+		.pm = pm_ptr(&wcd9378_sdw_pm_ops),
+	}
+};
+module_sdw_driver(wcd9378_sdw_driver);
+
+MODULE_DESCRIPTION("WCD9378 SDW codec driver");
+MODULE_LICENSE("GPL");

sound/soc/codecs/wcd9378.h

@@ -0,0 +1,246 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2026, Jorijn van der Graaf
+ *
+ * Register map for the Qualcomm WCD9378 audio codec.
+ *
+ * The codec exposes its control registers in the SoundWire SDCA control
+ * address space (bit 30 set, SDCA function number in bits 25:22), accessed
+ * through the TX SoundWire slave. The analog core registers (function 0,
+ * implementation-defined region at +0x180000) are layout-compatible with
+ * the WCD937x family; on top of that the chip adds SDCA-style functions
+ * (SmartMIC0/1/2, SmartJACK, SmartAMP) whose sequencers drive the analog
+ * power-up autonomously.
+ */
+
+#ifndef __WCD9378_H__
+#define __WCD9378_H__
+
+#include <linux/regmap.h>
+#include <linux/soundwire/sdw.h>
+#include <linux/soundwire/sdw_type.h>
+#include <sound/soc.h>
+
+/* SDCA function 0 (extension unit): device identity */
+#define WCD9378_FUNC_EXT_ID_0			0x40000048
+#define WCD9378_FUNC_EXT_ID_1			0x40000049
+#define WCD9378_FUNC_EXT_VER			0x40000050
+#define WCD9378_FUNC_STAT			0x40080000
+#define WCD9378_DEV_MANU_ID_0			0x40100060
+#define WCD9378_DEV_MANU_ID_1			0x40100061
+#define WCD9378_DEV_PART_ID_0			0x40100068
+#define WCD9378_DEV_PART_ID_1			0x40100069
+#define WCD9378_DEV_VER				0x40100070
+
+/* Analog core (WCD937x-compatible layout), function 0 + 0x180000 */
+#define WCD9378_ANA_PAGE			0x40180000
+#define WCD9378_ANA_BIAS			0x40180001
+#define WCD9378_ANA_BIAS_ANALOG_BIAS_EN		BIT(7)
+#define WCD9378_ANA_BIAS_PRECHRG_EN		BIT(6)
+#define WCD9378_ANA_RX_SUPPLIES			0x40180008
+#define WCD9378_ANA_TX_CH1			0x4018000e
+#define WCD9378_ANA_TX_CH2			0x4018000f
+#define WCD9378_ANA_TX_CH2_HPF1_INIT		BIT(6)
+#define WCD9378_ANA_TX_CH2_HPF2_INIT		BIT(5)
+#define WCD9378_ANA_TX_CH3			0x40180010
+#define WCD9378_ANA_TX_CH3_HPF			0x40180011
+#define WCD9378_ANA_TX_CH3_HPF3_INIT		BIT(6)
+#define WCD9378_ANA_TX_GAIN_MASK		GENMASK(4, 0)
+#define WCD9378_ANA_MICB1			0x40180022
+#define WCD9378_ANA_MICB2			0x40180023
+#define WCD9378_ANA_MICB2_RAMP			0x40180024
+#define WCD9378_ANA_MICB2_RAMP_SHIFT_CTL_MASK	GENMASK(4, 2)
+#define WCD9378_ANA_MICB2_RAMP_EN		BIT(7)
+#define WCD9378_ANA_MICB3			0x40180025
+#define WCD9378_BIAS_VBG_FINE_ADJ		0x40180029
+#define WCD9378_MBHC_CTL_SPARE_1		0x40180058
+#define WCD9378_MICB1_TEST_CTL_2		0x4018006c
+#define WCD9378_MICB2_TEST_CTL_2		0x4018006f
+#define WCD9378_MICB3_TEST_CTL_2		0x40180072
+#define WCD9378_TX_COM_TXFE_DIV_CTL		0x4018007b
+#define WCD9378_TX_COM_TXFE_DIV_SEQ_BYPASS	BIT(7)
+#define WCD9378_SLEEP_CTL			0x40180103
+#define WCD9378_SLEEP_CTL_BG_CTL_MASK		GENMASK(3, 1)
+#define WCD9378_SLEEP_CTL_BG_EN			BIT(7)
+#define WCD9378_SLEEP_CTL_LDOL_BG_SEL		BIT(6)
+#define WCD9378_TX_NEW_CH12_MUX			0x4018012e
+#define WCD9378_TX_NEW_CH12_MUX_CH1_SEL_MASK	GENMASK(2, 0)
+#define WCD9378_TX_NEW_CH12_MUX_CH2_SEL_MASK	GENMASK(5, 3)
+#define WCD9378_TX_NEW_CH34_MUX			0x4018012f
+#define WCD9378_TX_NEW_CH34_MUX_CH3_SEL_MASK	GENMASK(2, 0)
+#define WCD9378_HPH_RDAC_GAIN_CTL		0x40180132
+#define WCD9378_HPH_RDAC_HD2_CTL_L		0x40180133
+#define WCD9378_HPH_RDAC_HD2_CTL_R		0x40180136
+
+/* Digital page */
+#define WCD9378_TOP_CLK_CFG			0x40180407
+#define WCD9378_CDC_ANA_TX_CLK_CTL		0x40180417
+#define WCD9378_CDC_ANA_TXSCBIAS_CLK_EN		BIT(0)
+#define WCD9378_CDC_AMIC_CTL			0x4018045a
+#define WCD9378_PDM_WD_CTL0			0x40180465
+#define WCD9378_PDM_WD_CTL1			0x40180466
+#define WCD9378_EFUSE_REG_16			0x401804c0
+#define WCD9378_EFUSE_REG_29			0x401804cd
+#define WCD9378_PLATFORM_CTL			0x401804f0
+
+/* Sequencer block (SEQR) */
+#define WCD9378_SYS_USAGE_CTRL			0x40180501
+#define WCD9378_SYS_USAGE_CTRL_MASK		GENMASK(3, 0)
+#define WCD9378_HPH_UP_T0			0x40180510
+#define WCD9378_HPH_UP_T9			0x40180519
+#define WCD9378_HPH_DN_T0			0x4018051b
+#define WCD9378_SEQ_TX0_STAT			0x40180592
+#define WCD9378_SEQ_TX1_STAT			0x40180593
+#define WCD9378_SEQ_TX2_STAT			0x40180594
+#define WCD9378_MICB_REMAP_TABLE_VAL_3		0x401805a3
+#define WCD9378_MICB_REMAP_TABLE_VAL_4		0x401805a4
+#define WCD9378_MICB_REMAP_TABLE_VAL_5		0x401805a5
+#define WCD9378_SM0_MB_SEL			0x401805b0
+#define WCD9378_SM1_MB_SEL			0x401805b1
+#define WCD9378_SM2_MB_SEL			0x401805b2
+#define WCD9378_SM_MB_SEL_MASK			GENMASK(1, 0)
+#define WCD9378_MB_PULLUP_EN			0x401805b3
+
+/* SmartAMP SDCA function */
+#define WCD9378_SMP_AMP_FUNC_STAT		0x40880000
+#define WCD9378_SMP_AMP_FUNC_ACT		0x40880008
+
+/* SmartJACK SDCA function (hosts ADC2 when fed from AMIC2) */
+#define WCD9378_CMT_GRP_MASK			0x40c00008
+#define WCD9378_SMP_JACK_IT31_MICB		0x40c00798
+#define WCD9378_SMP_JACK_IT31_USAGE		0x40c007a0
+#define WCD9378_SMP_JACK_PDE34_REQ_PS		0x40c00808
+#define WCD9378_SMP_JACK_FUNC_STAT		0x40c80000
+#define WCD9378_SMP_JACK_FUNC_ACT		0x40c80008
+#define WCD9378_SMP_JACK_PDE34_ACT_PS		0x40c80800
+
+/* SmartMIC0/1/2 SDCA functions (ADC1/ADC2/ADC3 sequencers) */
+#define WCD9378_SMP_MIC_BASE(n)			(0x41000000 + (n) * 0x400000)
+#define WCD9378_SMP_MIC_IT11_MICB(n)		(WCD9378_SMP_MIC_BASE(n) + 0x98)
+#define WCD9378_SMP_MIC_IT11_USAGE(n)		(WCD9378_SMP_MIC_BASE(n) + 0xa0)
+#define WCD9378_SMP_MIC_PDE11_REQ_PS(n)		(WCD9378_SMP_MIC_BASE(n) + 0x108)
+#define WCD9378_SMP_MIC_OT10_USAGE(n)		(WCD9378_SMP_MIC_BASE(n) + 0x3a0)
+#define WCD9378_SMP_MIC_FUNC_STAT(n)		(WCD9378_SMP_MIC_BASE(n) + 0x80000)
+#define WCD9378_SMP_MIC_FUNC_ACT(n)		(WCD9378_SMP_MIC_BASE(n) + 0x80008)
+#define WCD9378_SMP_MIC_PDE11_ACT_PS(n)		(WCD9378_SMP_MIC_BASE(n) + 0x80100)
+
+#define WCD9378_MAX_REGISTER			0x41900070
+
+/*
+ * Raw (16-bit, non-paged) Qualcomm slave SCP registers, written with
+ * sdw_write() directly. Bus clock indication towards the codec and
+ * SDCA interrupt type configuration.
+ */
+#define WCD9378_SWRS_SCP_BASE_CLK		0x4d
+#define WCD9378_SWRS_SCP_BUSCLK_SCALE_BANK0	0x62
+#define WCD9378_SWRS_SCP_BUSCLK_SCALE_BANK1	0x72
+#define WCD9378_SWRS_SCP_SDCA_INTRTYPE_1	0xf4
+#define WCD9378_SWRS_SCP_SDCA_INTRTYPE_2	0xf8
+#define WCD9378_SWRS_SCP_SDCA_INTRTYPE_3	0xfc
+#define WCD9378_SWRS_SCP_HOST_CLK_DIV2_CTL(m)	(0xe0 + 0x10 * (m))
+#define WCD9378_SWRS_BASE_CLK_19P2MHZ		0x01
+#define WCD9378_SWRS_CLK_SCALE_DIV2		0x02	/* 9.6 MHz */
+#define WCD9378_SWRS_CLK_SCALE_DIV4		0x03	/* 4.8 MHz */
+
+/* ITxx_USAGE ADC mode values */
+#define WCD9378_ADC_USAGE_HIFI			0x01
+#define WCD9378_ADC_USAGE_LO_HIF		0x02
+#define WCD9378_ADC_USAGE_NORMAL		0x03
+#define WCD9378_ADC_USAGE_LP			0x05
+#define WCD9378_ADC_USAGE_OFF			0x00
+
+/* ITxx_MICB usage values */
+#define WCD9378_MICB_USAGE_OFF			0x00
+#define WCD9378_MICB_USAGE_PULL_DOWN		0x01
+#define WCD9378_MICB_USAGE_1P2V			0x02
+#define WCD9378_MICB_USAGE_1P8V_OR_PULLUP	0x03
+#define WCD9378_MICB_USAGE_2P5V			0x04
+#define WCD9378_MICB_USAGE_2P75V		0x05
+#define WCD9378_MICB_USAGE_2P2V			0xf0
+#define WCD9378_MICB_USAGE_2P7V			0xf1
+#define WCD9378_MICB_USAGE_2P8V			0xf2
+#define WCD9378_MICB_USAGE_REMAP_TABLE_3	0xf3
+#define WCD9378_MICB_USAGE_REMAP_TABLE_4	0xf4
+#define WCD9378_MICB_USAGE_REMAP_TABLE_5	0xf5
+
+/* PDExx_REQ_PS power states */
+#define WCD9378_PDE_PS0_ON			0x00
+#define WCD9378_PDE_PS3_OFF			0x03
+
+#define WCD9378_MAX_MICBIAS			3
+#define WCD9378_MAX_SWR_CH_IDS			15
+#define WCD9378_SWRM_CH_MASK(ch_idx)		BIT((ch_idx) - 1)
+
+enum wcd9378_tx_sdw_ports {
+	WCD9378_ADC_1_PORT = 1,
+	WCD9378_ADC_2_PORT,
+	WCD9378_ADC_3_PORT,
+	WCD9378_DMIC_0_1_MBHC_PORT,
+	WCD9378_DMIC_2_5_PORT,
+	WCD9378_MAX_TX_SWR_PORTS = WCD9378_DMIC_2_5_PORT,
+};
+
+enum wcd9378_rx_sdw_ports {
+	WCD9378_HPH_PORT = 1,
+	WCD9378_CLSH_PORT,
+	WCD9378_COMP_PORT,
+	WCD9378_LO_PORT,
+	WCD9378_DSD_PORT,
+	WCD9378_MAX_SWR_PORTS = WCD9378_DSD_PORT,
+};
+
+enum wcd9378_tx_sdw_channels {
+	WCD9378_ADC1,
+	WCD9378_ADC2,
+	WCD9378_ADC3,
+	WCD9378_DMIC0,
+	WCD9378_DMIC1,
+	WCD9378_MBHC,
+	WCD9378_DMIC2,
+	WCD9378_DMIC3,
+	WCD9378_DMIC4,
+	WCD9378_DMIC5,
+};
+
+enum wcd9378_rx_sdw_channels {
+	WCD9378_HPH_L,
+	WCD9378_HPH_R,
+	WCD9378_CLSH,
+	WCD9378_COMP_L,
+	WCD9378_COMP_R,
+	WCD9378_LO,
+	WCD9378_DSD_L,
+	WCD9378_DSD_R,
+};
+
+struct wcd9378_priv;
+struct wcd9378_sdw_priv {
+	struct sdw_slave *sdev;
+	struct sdw_stream_config sconfig;
+	struct sdw_stream_runtime *sruntime;
+	struct sdw_port_config port_config[WCD9378_MAX_SWR_PORTS];
+	struct wcd_sdw_ch_info *ch_info;
+	bool port_enable[WCD9378_MAX_SWR_CH_IDS];
+	unsigned int master_channel_map[SDW_MAX_PORTS];
+	int active_ports;
+	bool is_tx;
+	struct wcd9378_priv *wcd9378;
+	struct regmap *regmap;
+};
+
+#if IS_ENABLED(CONFIG_SND_SOC_WCD9378_SDW)
+int wcd9378_sdw_hw_params(struct wcd9378_sdw_priv *wcd,
+			  struct snd_pcm_substream *substream,
+			  struct snd_pcm_hw_params *params,
+			  struct snd_soc_dai *dai);
+#else
+static inline int wcd9378_sdw_hw_params(struct wcd9378_sdw_priv *wcd,
+					struct snd_pcm_substream *substream,
+					struct snd_pcm_hw_params *params,
+					struct snd_soc_dai *dai)
+{
+	return -EOPNOTSUPP;
+}
+#endif
+
+#endif /* __WCD9378_H__ */

sound/soc/qcom/qdsp6/q6apm-lpass-dais.c

@@ -224,6 +224,21 @@ static int q6apm_lpass_dai_prepare(struct snd_pcm_substream *substream, struct s
 		dev_err(dai->dev, "Failed to prepare Graph %d\n", rc);
 		goto err;
 	}
+
+	/*
+	 * Start the port already at prepare, like q6afe does: this starts
+	 * the interface clocks before the DAPM power-up sequence runs, so
+	 * codecs that need a live BCLK at power-up (e.g. aw88261) can
+	 * start synchronously. The trigger callback keeps its start as a
+	 * no-op fallback via is_port_started.
+	 */
+	rc = q6apm_graph_start(dai_data->graph[dai->id]);
+	if (rc < 0) {
+		dev_err(dai->dev, "Failed to start APM port %d\n", dai->id);
+		goto err;
+	}
+	dai_data->is_port_started[dai->id] = true;
+
 	return 0;
 err:
 	if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {

sound/soc/qcom/sc8280xp.c

@@ -34,6 +34,7 @@ static int sc8280xp_snd_init(struct snd_soc_pcm_runtime *rtd)
 	switch (cpu_dai->id) {
 	case PRIMARY_MI2S_RX...QUATERNARY_MI2S_TX:
 	case QUINARY_MI2S_RX...QUINARY_MI2S_TX:
+	case SENARY_MI2S_RX...SENARY_MI2S_TX:
 		snd_soc_dai_set_fmt(cpu_dai, SND_SOC_DAIFMT_BP_FP);
 		break;
 	case WSA_CODEC_DMA_RX_0: